Partial and total splenectomies are associated with a high risk of substantial blood loss. Lasers operating at wavelengths strongly absorbed by water have the potential to improve hemostasis and cut while providing a narrow zone of thermal damage. The aim of this study is to compare a thulium-doped fiber laser (TDFL) emitting a wavelength of 1940 nm and a diode laser (DL) operating at 1470 nm for spleen surgery in a pig model. A partial splenectomy and spleen incisions were made in 12 animals using the two laser devices. The hemostasis was evaluated visually during surgeries. Post-mortem and histopathological evaluations were done on days 0, 7, and 14 following surgery. Neither TDFL nor DL caused bleeding on day 0 or delayed bleeding. On day 14, pale streaks at the site of incision were slightly wider after cutting with DL than with TDFL. Histological analysis revealed a carbonized zone with exudation and a deeper zone of thermal tissue damage on day 0. The width of the thermal changes was 655.26 ± 107.70 μm for TDFL and 1413.37 ± 111.85 μm for DL. On day 7, a proliferation of fibroblasts and splenocytes was visible, as well as a formation of multinucleated giant cells adjacent to the residues of carbonization. The zone of thermal damage was broader for DL (1157.5 ± 262.77 μm) than for TDFL (682.22 ± 116.58 μm). On day 14, cutting sites were filled with connective and granulation tissues with the residues of carbonization. The zone of thermal damage was narrower for TDFL (761.65 ± 34.3 μm) than for DL (1609.82 ± 202.22 μm). Thus, both lasers are efficient in spleen surgery, providing good hemostasis. However, TDFL produces a narrower zone of thermal damage, which suggests its better efficiency for spleen surgery, especially when performing more precise procedures.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7085013PMC
http://dx.doi.org/10.3390/ma13051167DOI Listing

Publication Analysis

Top Keywords

zone thermal
20
spleen surgery
16
thermal damage
16
thulium-doped fiber
8
fiber laser
8
diode laser
8
pig model
8
bleeding day
8
μm tdfl
8
μm day
8

Similar Publications

Thermal cracking is one of the serious issues that deteriorates the processibility of laser powder bed fusion (LPBF) high-strength aluminum components. To date, the effects of processing parameters on crack formation are still not well understood. The purpose of this study is to understand the correlation between the thermal cycle and the hot cracking during LPBF of Al-Cu-Mg-Mn alloys.

View Article and Find Full Text PDF

A three-dimensional numerical model of the vacuum sintering furnace was established, combined with the custom program of temperature-voltage feedback regulation. Through simulationand experimental validation, the heating and holding stage as well as the thermal hysteresis phenomenon of the furnace were analyzed, a dimensionless quantity of hysteresis temperature difference was proposed and calculated, the distribution of the electric field and temperature uniformity of the furnace were discussed in detail, while the structural improvement approach was proposed based on simulation. The results show that: during the heating process, the maximum of thermal hysteresis temperature difference between the graphite cylinder and the heating tube is 0.

View Article and Find Full Text PDF

Cryogel Addition Effect on Ultrasound-Assisted Thawing of Pork Meat.

Int J Food Sci

December 2024

Laboratory 13 Thermal and Structural Analysis of Materials and Foods, Multidisciplinary Research Unit, National Autonomous University of Mexico-Superior Studies Faculty at Cuautitlan (UNAM-FESC), Cuautitlan Izcalli, Mexico State, Mexico.

The use of new technologies that allow for improving conventional food preservation processes is what the industry has been adopting in recent decades, with high-intensity ultrasound (US) and the application of cryoprotectant agents (cryogels) being those that have become more relevant today. For this reason, in this study, cuts of pork frozen in liquid nitrogen with and without waxy starch cryogel and thawed under controlled conditions in water immersion and with US were used, evaluating thermal parameters such as the initial zone and the melting rate of ice crystals and quality parameters such as pH, water holding capacity (WHC), microstructure, color profile, shear force, and surface changes. It was shown that the addition of cryogel modifies the initial fusion zone, that US-assisted thawing increases the fusion rate, and that both factors influence the quality parameters.

View Article and Find Full Text PDF

Safety learning during threat and adversity is critical for behavioral adaptation, resiliency, and survival. Using a novel mouse paradigm involving thermal threat, we recently demonstrated that safety learning is highly susceptible to social isolation stress. Yet, our previous study primarily considered male mice and did not thoroughly scrutinize the relative impacts of stress on potentially distinct defensive mechanisms implemented by males and females during the thermal safety task.

View Article and Find Full Text PDF

In this study we monitored exposure to airborne dust in workers performing various tasks at two biomass-fuelled thermal power plants (27 and 46 MW) over six years. The plants are mainly fuelled by forest wood chips and, to a lesser extent, by agro-food products, with annual consumption of about 300 and 450 kt. We focused on inhalable wood dust because of its potential carcinogenicity to humans.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!