Purpose: To evaluate the surface roughness values of zirconium oxide samples that were gradually polished using a commercially available polishing system and polishing paste.
Materials And Methods: A total of 50 rectangular specimens of predetermined size (10 × 10 × 3 mm) were sintered from zirconium oxide. Samples were randomly assigned to one of five groups (n = 10 each): control, coarse (Co), fine (F), super fine (SF), or polishing paste (PP). In the control group, no polishing was done; in the Co group, a coarse polisher was used; and the specimens in the remaining three groups underwent additional processing with a fine rubber abrasive. For SF and PP samples, subsequent treatment with a super fine polisher was applied. Finally, for the PP group, a goat-hair brush with diamond polishing paste was used. An optical profilometer was used to evaluate roughness average (Ra) in micrometers (μm). ANOVA and Games-Howell post hoc tests were utilized to detect differences between groups. The significance level was set to α = .05.
Results: Surface roughness gradually decreased with further polishing throughout the groups: control Ra = 0.525 ± 0.099 μm; Co Ra = 0.252 ± 0.038 μm; F Ra = 0.196 ± 0.035 μm; SF Ra = 0.114 ± 0.031 μm; and PP Ra = 0.054 ± 0.020 μm. Statistically significant differences were detected among all groups (P < .05).
Conclusion: A surface roughness of 0.054 μm can be achieved if a full zirconia polishing protocol is used. Zirconium oxide can be polished to various surface roughnesses using commercially available polishing products.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.11607/ijp.6686 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Physical-mechanical properties and accuracy of additively manufactured resin denture bases: Impact of printing orientation.
J Prosthodont Res
January 2025
Department of Prosthodontics, Faculty of Dentistry, Ibb University, Ibb, Yemen.
Purpose: This systematic review evaluated the effect of different printing orientations on the physical-mechanical properties and accuracy of resin denture bases and related specimens.
Study Selection: Utilizing PRISMA 2020 guidelines, a comprehensive search of PubMed, Web of Science, Cochrane, and Scopus databases was conducted until June 2024. Included studies examined the accuracy, volumetric changes, and mechanical or physical properties of 3D-printed denture bases in various orientations.
Preparation and physicochemical characterization of different biocomposite films blended with bacterial exopolysaccharide EPS MC-5 and bacteriocin for food packaging applications.
Int J Biol Macromol
January 2025
Department of Biotechnology, School of Life Sciences, Pondicherry University, Puducherry 605014, India. Electronic address:
The study aims to evaluate how bacteriocin and extracellular polymeric substances (EPS) can influence the development of active packaging for food. The components might enhance the performance of packaging materials in terms of their physicochemical properties and their effectiveness in preserving food. Bacteriocin and EPS exert a significant effect in blocking the transmission of UV and visible light radiations.
View Article and Find Full Text PDFImprovement of glucose detection using 10 nm AlO thin film on diamond solution-gate field-effect transistor.
Talanta
January 2025
Key Laboratory for Physical Electronics and Devices of the Ministry of Education & School of Science & Shaanxi Key Laboratory of Information Photonic Technique & Institute of Wide Bandgap Semiconductors, Xi'an Jiaotong University, Xi'an, 710049, China. Electronic address:
Glucose detection is crucial for diagnosis, prevention and treatment of diabetes mellitus. In this work, 10 nm AlO thin film was introduced on the channel of diamond solution-gate field-effect transistor (SGFET) to improve the performance of glucose detection. AFM results show the roughness of channel surface increased after AlO thin film deposition.
View Article and Find Full Text PDFMicrochannel fabrication on bio-grade Nitinol SMA by μ-ED milling process using sustainable oil for improving the machining performance and biocompatibility.
Biofabrication
January 2025
Mechanical Engineering, National Institute of Technology Meghalaya, Shillong, Shillong, Meghalaya, 793003, INDIA.
The process of micromachining has garnered attention for its ability to create three-dimensional tiny features, particularly in ultra-hard and exotic materials. The present work investigates the effect of different parameters of the µ-ED milling, such as pulse on time (Ton), pulse off time (Toff), voltage (V), and tool rotation (TR) on the dimensional deviation (DD), material removal rate (MRR), surface roughness (Ra), and machined surface characteristics (analysed by EDS and FESEM). The sesame oil as dielectric and tungsten-copper as tool electrodes were used to maintain the accuracy and improve the machinability of bio-grade Nitinol SMA.
View Article and Find Full Text PDFStudy on the effect of acid fracturing fluid on pore structure of middle to high rank coal.
Sci Rep
January 2025
College of Mining, Guizhou University, Guiyang, 550025, Guizhou, China.
Acid fracturing fluids can effectively improve the microporous structure of coal, thereby enhancing the permeability of coal seam and the efficiency of gas drainage. To explore the effects of acid fracturing fluids on the pore structure modification of coal samples from different coal ranks, hydrochloric acid-based acid fracturing fluids were prepared and used to soak four types of medium to high-rank coal in an experiment. High-pressure mercury intrusion and liquid nitrogen adsorption techniques results demonstrated that the acid fracturing fluid can effectively alter the pore structure of coal.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!