Meat quality characteristics of the Arabian camel (Camelus dromedarius) at different ages and post-mortem ageing periods.

Asian-Australas J Anim Sci

Department of Agricultural Engineering, College of Food and Agricultural Sciences, King Saud University, P.O Box 2460, 11451 Riyadh, Saudi Arabia.

Published: August 2020

Objective: Meat quality characteristics and sensory attributes were evaluated in three age groups (12, 18, and 24 mo) of one-humped camels of the Saudi Arabian Najdi breed.

Methods: Thirty-six male camels (12 for each age group) were used. The Longissimus dorsi muscle from each carcass was divided into three parts and subjected to three ageing periods (1, 5, or 10 d) and evaluated for shear force, myofibril fragmentation index (MFI), expressed juice, cooking loss, and sensory attributes.

Results: Age had a significant effect on shear force, MFI, expressed juice quantity, and organoleptic properties. Camels slaughtered at 12 mo exhibited lower shear force and MFI, and higher expressed juice quantity, tenderness, juiciness, and overall acceptability than those slaughtered at 24 mo. Ageing had a significant influence on shear force, MFI, expressed juice quantity, but not on cooking loss. Camel meat aged for 10 d exhibited significantly lower shear force values and expressed juice quantity, and significantly higher MFI compared to that aged for 1 d. However, ageing did not significantly affect sensory attributes, except for tenderness, in camels slaughtered at 18 mo.

Conclusion: Both instrumental and sensory evaluations showed that young camel meat has desirable quality characteristics, with superior tenderness and juiciness.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7322637PMC
http://dx.doi.org/10.5713/ajas.19.0589DOI Listing

Publication Analysis

Top Keywords

shear force
20
expressed juice
20
juice quantity
16
quality characteristics
12
mfi expressed
12
force mfi
12
meat quality
8
ageing periods
8
sensory attributes
8
cooking loss
8

Similar Publications

Introduction: Biofilms may show varying adherence strengths to dentine. This study quantified the shear force required for the detachment of multispecies biofilm from the dentine using fluid dynamic gauging (FDG) and computation fluid dynamics (CFD). To date this force has not been quantified.

View Article and Find Full Text PDF

The iron-regulated surface determinant protein B (IsdB) has recently been shown to bind to toll-like receptor 4 (TLR4), thereby inducing a strong inflammatory response in innate immune cells. Currently, two unsolved questions are (i) What is the molecular mechanism of the IsdB-TLR4 interaction? and (ii) Does it also play a role in nonimmune systems? Here, we use single-molecule experiments to demonstrate that IsdB binds TLR4 with both weak and extremely strong forces and that the mechanostability of the molecular complex is dramatically increased by physical stress, sustaining forces up to 2000 pN, at a loading rate of 10 pN/s. We also show that TLR4 binding by IsdB mediates time-dependent bacterial adhesion to endothelial cells, pointing to the role of this bond in cell invasion.

View Article and Find Full Text PDF

Microfluidic chips are powerful tools for investigating numerous variables including chemical and physical parameters on protein aggregation. This study investigated the aggregation of bovine serum albumin (BSA) in two different systems: a vial-based static system and a microfluidic chip-based dynamic system in which BSA aggregation was induced successfully. BSA aggregation induced in a microfluidic chip on a timescale of seconds enabled a dynamic investigation of the forces driving the aggregation process.

View Article and Find Full Text PDF

The ore mining sites commonly experience slope instability, which is causing concern for the workers' safety and the operation's stability. Considering the Ziluoyi iron ore mining site as a case study, uniaxial compression strength and shear tests are performed on the lower disk peripheral rock, ore body, and upper disk peripheral rock, leading to the extraction of compressive strength and elastic modulus (lower disk: 77.7 MPa-9.

View Article and Find Full Text PDF

Repetitive manual labor tasks involving twisting, bending, and lifting commonly lead to lower back and knee injuries in the workplace. To identify tasks with high injury risk, we recruited N = 9 participants to perform industry-relevant, 2-handed lifts with a 11-kg weight. These included symmetrical/asymmetrical, ascending/descending lifts that varied in start-to-end heights (knee-to-waist and waist-to-shoulder).

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!