This paper shows results of a study on the corrosion behavior of micro-arc oxidation (MAO) coatings sampled from the AlMg6 alloy. The alloy was simultaneously subjected to a corrosive environment and static tensile stress. For comparative purposes, the tests were run for both coated samples and samples without coatings. The research was conducted at a properly prepared stand; the samples were placed in a glass container filled with 3.5% NaCl aqueous solution and stretched. Two levels of tensile stress were accepted for the samples: = 0.8 = , and the tests were run for two time intervals: = 480 h and = 1000 h. Prolonged stress corrosion tests (lasting up to 1000 h) showed that the samples covered with ceramic coatings demonstrated significantly higher corrosion resistance than the samples without the coatings. Protective properties of the coating could be explained by its structure. Surface pores were insignificant, and their depth was very limited. The porosity level of the main coating layer was 1%. Such a structure of coating and its phase composition provided high protective properties.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7013523 | PMC |
| http://dx.doi.org/10.3390/ma13020356 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
High-Performance Hydrogen Sensing at Room Temperature via Nb-Doped Titanium Oxide Thin Films Fabricated by Micro-Arc Oxidation.
Nanomaterials (Basel)
January 2025
Guangdong Key Laboratory of Materials and Equipment in Harsh Marine Environment, School of Ocean Engineering, Guangzhou Maritime University, Guangzhou 510725, China.
Metal oxide semiconductor (MOS) hydrogen sensors offer advantages, such as high sensitivity and fast response, but their challenges remain in achieving low-cost fabrication and stable operation at room temperature. This study investigates Nb-doped TiO (NTO) thin films prepared via a one-step micro-arc oxidation (MAO) with the addition of NbO nanoparticles into the electrolyte for room-temperature hydrogen sensing. The characterization results revealed that the incorporation of NbO altered the film's morphology and phase composition, increasing the Nb content and forming a homogeneous composite thin film.
View Article and Find Full Text PDFImproving Anti-Corrosion Property of Aluminium Alloy by Fabrication MAO Coating via Mixing Titanium Potassium Oxalate into Electrolyte.
Molecules
January 2025
Nanyang Branch of Henan Boiler and Pressure Vessel Inspection Technology Research Institute, No. 1088 Gongye South Road, Nanyang 473000, China.
Titanium potassium oxalate had been mixed into the electrolyte to improve the anti-corrosion property of the micro arc oxidation coating on the surface of the aluminium alloy. The surface and cross-section of the coating at different titanium potassium oxalate concentrations had been observed by scanning electron microscopy, showing that when the titanium potassium oxalate concentration was 10 g/L, the coating compactness was better. Additionally, the element content of the coating had been studied by the energy dispersive spectrometer, and results proved that the coating consisted of Al, O, Ti, Si, and P.
View Article and Find Full Text PDFThe combustion of lemon peel oil/gasoline blends in spark ignition engine with high-insulation piston crown coating.
Sci Rep
November 2024
Department of Mechanical Engineering, Wollo University, Kombolcha Institute of Technology, 208, Kombolcha, Ethiopia.
Article Synopsis
- - The study focused on recovering oil from discarded lemon peel biomass and testing it as a gasoline substitute in engine blends at different volume ratios (10%, 20%, and 30%) using steam distillation for oil extraction.
- - Using an endoscopic visualization approach, the research found that a 10% lemon peel oil blend offered higher thermal efficiency and lower emissions, while premixed combustion produced better combustion characteristics, leading to increased cylinder pressure.
- - To enhance performance, a ceramic coating was applied to the piston using the micro-arc oxidation technique, which improved thermal efficiency by 3% and 4.69% for the 20% lemon peel oil blend compared to uncoated and pure gasoline engines, while also reducing hydrocarbon
Incorporation of cerium oxide nanoparticles into the micro-arc oxidation layer promotes bone formation and achieves structural integrity in magnesium orthopedic implants.
Acta Biomater
January 2025
Department of Biomedical Engineering, National Cheng Kung University, Tainan, Taiwan; Medical Device Innovation Center, National Cheng Kung University, Tainan, Taiwan. Electronic address:
Biodegradable metals offer significant advantages by reducing the need for additional surgeries following bone fixation. These materials, with their optimal mechanical and degradable properties, also mitigate stress-shielding effects while promoting biological processes essential for healing. This study investigated the in vitro and in vivo biocompatibility of ZK60 magnesium alloy coated with a micro-arc oxidative layer incorporated with cerium oxide nanoparticles in orthopedic implants.
View Article and Find Full Text PDFOrganic-Inorganic Biocompatible Coatings for Temporary and Permanent Metal Implants.
Int J Mol Sci
October 2024
Department of Materials Science and Physics of Metals, Ufa University of Science and Technology, 450008 Ufa, Russia.
The general trend of increasing life expectancy will consistently drive the demand for orthopedic prostheses. In addition to the elderly, the younger population is also in urgent need of orthopedic devices, as bone fractures are a relatively common injury type; it is important to treat the patient quickly, painlessly, and eliminate further health complications. In the field of traumatology and orthopedics, metals and their alloys are currently the most commonly used materials.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!