Objective: The aim of this study was to determine the effects of preparation vs nonpreparation of tooth surfaces and the types of porcelain laminate veneers (PLVs) on color changes after 300 hours of artificially accelerated aging (AAA).
Materials And Methods: Forty extracted maxillary central incisors were used. The teeth were divided into four groups (n = 10) to evaluate preparation methods and porcelain types: Group A: tooth preparation with IPS e.max computer-assisted design (CAD), group B: tooth preparation with IPS e.max press, group C: nonpreparation with IPS e.max CAD, and group D: nonpreparation with IPS e.max press. Veneers were fabricated and cemented using a dual-polimerized cement. Initial color measurement was performed and repeated after AAA. Color changes were calculated with the CIEDE 2000 (ΔE ) formula. Color differences were analyzed with two-way ANOVA (P < .05).
Results: The two-way ANOVA test showed no significant difference among the groups (P > .05). The highest color change value was observed in group C, followed by groups B, A, and D.
Conclusion: Preparation of veneers caused more color changes in PLVs than nonpreparation. However, IPS e.max CAD systems for fabrication of nonprepared PLVs increased the color change of the PLVs measured after AAA.
Clinical Significance: The results provide information on the effect of the amount of preparation and the type of porcelain on color change in porcelain laminate veneers. In terms of esthetic dentistry, IPS e.max press and non-prep treatment should be used in the anterior region, where esthetics are important.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/jerd.12564 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Micro CT evaluation of marginal discrepancies of endocrown restored molars with different intrapulpal depths and materials of fabrication. (in-vitro study).
BMC Oral Health
January 2025
Faculty of dentistry, Ain Shams University, Cairo, Egypt.
Objective: The purpose of this study was to evaluate the effect of different preparation depths (0, 2 and 4 mm) of different restoration designs (classic endocrown design versus overlay design) on marginal adaptation of restorations fabricated of two different restorative materials (lithium disilicate and PEEK).
Materials And Methods: Sixty mandibular natural molars were collected as abutments for the restorations of this study, and grouped in three main groups of different cavity depths (0, 2 and 4). Each group was divided into two subgroups according to material of fabrication to (L) for lithium disilicate (IPS emax CAD, Ivoclar vivadent, Switzarland) and (P) for PEEK (Bio-hpp, Bredent, Germany).
Properties of New Partially Crystallized Lithium Disilicate CAD-CAM Materials.
Oper Dent
January 2025
*Kraig S. Vandewalle, DDS, MS, Col (ret), USAF, DC, Air Force Consultant in Dental Research Advanced Education in General Dentistry Residency, AF Postgraduate Dental School, Joint Base San Antonio - Lackland, TX, USA; Uniformed Services University of the Health Sciences, Bethesda, MD, USA.
Objective: The purpose of this study was to compare the optical, mechanical, and biological properties of two new, inexpensive lithium disilicate (LS2) materials (Lodden (LOD), LD Medical Technology; and BeautyZir (BZ), BeautyZir Technology) to a clinically established LS2 material (IPS e.max CAD (EMAX), Ivoclar Vivadent).
Methods And Materials: The optical properties of the translucency parameter (TP) and opalescence parameter (OP) were obtained with a dental spectrophotometer.
Repair Bond Strength of Composite Resin to Dental Ceramic Using Various Surface Treatments: An Study.
J Int Soc Prev Community Dent
October 2024
Department of Conservative Dentistry, College of Dentistry, University of Mosul, Mosul, Iraq.
Aim: This research aims to evaluate and compare the effect of various surface treatments and adhesive types on the bond strength between composite resin and two types of ceramic materials.
Materials And Methods: A total of 98 disk-shaped of 10 mm diameter and 4 mm thickness were fabricated for each of the zirconia (H. C.
Effect of thermomechanical aging on marginal fit of three CAD-CAM restorative materials: An in vitro study.
J Dent Res Dent Clin Dent Prospects
September 2024
Crown and Bridge Department, Faculty of Dental Medicine, Al Azhar University, Assiut, Egypt.
Background: The present study assessed the impact of thermomechanical aging on the marginal fit of hybrid ceramic, reinforced composite resin, and lithium disilicate ceramic.
Methods: Eighteen human upper first premolars freshly extracted for orthodontic purposes were used to fabricate 18 CAD-CAM veneers and divided into three groups based on materials used: group H (n=6): hybrid ceramics (Vita Enamic), group R (n=6): reinforced composite resin (Brilliant crios), and group L (n=6): lithium disilicate ceramic (IPS e-max CAD). Each material's cementation procedure was carried out according to the manufacturer's instructions.
Do all ceramic and composite CAD-CAM materials exhibit equal bonding properties to implant Ti-base materials? An Interfacial Fracture Toughness Study.
Dent Mater
October 2024
Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), Liège, Belgium. Electronic address:
Objectives: To compare the interfacial fracture toughness (IFT) with or without aging, of four different classes of CAD-CAM ceramic and composite materials bonded with self-adhesive resin cement to titanium alloy characteristic of implant abutments.
Methods: High translucent zirconia (Katana; KAT), lithium disilicate-based glass-ceramic (IPS. emax.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!