Full-field spectroscopic measurement of the X-ray beam from a multilayer monochromator using a hyperspectral X-ray camera.

J Synchrotron Radiat

Radiation Physics Research Group - UGCT, Department of Physics and Astronomy, Ghent University, Proeftuinstraat 86/N12, B-9000 Gent, Belgium.

Published: January 2020

Multilayer monochromator devices are commonly used at (imaging) beamlines of synchrotron facilities to shape the X-ray beam to relatively small bandwidth and high intensity. However, stripe artefacts are often observed and can deteriorate the image quality. Although the intensity distribution of these artefacts has been described in the literature, their spectral distribution is currently unknown. To assess the spatio-spectral properties of the monochromated X-ray beam, the direct beam has been measured for the first time using a hyperspectral X-ray detector. The results show a large number of spectral features with different spatial distributions for a [Ru, BC] strip monochromator, associated primarily with the higher-order harmonics of the undulator and monochromator. It is found that their relative contributions are sufficiently low to avoid an influence on the imaging data. The [V, BC] strip suppresses these high-order harmonics even more than the former, yet at the cost of reduced efficiency.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6927514PMC
http://dx.doi.org/10.1107/S1600577519015212DOI Listing

Publication Analysis

Top Keywords

x-ray beam
12
multilayer monochromator
8
hyperspectral x-ray
8
x-ray
5
full-field spectroscopic
4
spectroscopic measurement
4
measurement x-ray
4
beam
4
beam multilayer
4
monochromator
4

Similar Publications

Aim: The aim of this cross-sectional prospective study was to evaluate the bone density changes around the bicortical corticobasal implant placed in the maxilla over 18 months of follow-up using cone-beam computed tomography (CBCT), focusing on the comparison between the anterior and posterior teeth and regions.

Materials And Methods: Thirty-five subjects (20, 53.26%, were males, and 15, 46.

View Article and Find Full Text PDF

Aim: This study aimed to evaluate the impact of a combination of immediate implant placement with maxillary sinus augmentation (MSA) solely using platelet-rich fibrin (PRF) on guided bone regeneration.

Materials And Methods: An interventional before-after (pre-post) study design was used with 30 dental patients (≥18 years of age; 14 males and 16 females) with initial bone heights ranging between 4 and 6 mm. Following the general check-up and the creation of a study model, the planned implant location demonstrated an external right maxilla diameter of more than 5 mm, thereby validating the cone-beam computed tomography (CBCT) radiograph.

View Article and Find Full Text PDF

Background: The foramen of Huschke (FH) and the petrotympanic fissure (PTF) are anatomical structures that can influence temporomandibular joint disorders (TMD) by potentially affecting the movement and function of the mandibular condyle.

Objective: This study investigates the relationship between patients with TMD and the presence of FH and PTF to enhance diagnostic and therapeutic approaches.

Methods: This retrospective study analyzed cone beam computed tomography (CBCT) images from 212 patients.

View Article and Find Full Text PDF

Although the modulus of elasticity of the human periodontal ligament (E) values used in dentistry widely ranged from 0.01 to 175 MPa, the exact E value has not been determined. This study aimed to verify whether and how E values affect the stress distribution over the tooth and periodontium structures, and to determine the appropriate E range.

View Article and Find Full Text PDF

Two experimental methods to integrate intra-oral scans into 3D stereophotogrammetric facial images.

Clin Oral Investig

January 2025

Department of Dentistry Section Orthodontics and Craniofacial Biology, Radboud University Medical Center, P.O. Box 9101, Nijmegen, 6500 HB, The Netherlands.

Objectives: For this research two different ways for integrating intra-oral scans into three-dimensional (3D) stereophotogrammetric images are analyzed and compared to the gold standard method.

Materials And Methods: A cross-sectional study was performed. For each patient a complete dataset was collected, which was used to generate 3D fusion models by three different methods: method A using cheek retractors, method B using a tracer and method C using full-skull CBCT.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!