A series of Au@Void@TiO yolk-shell structures were synthesized and characterized, and their catalytic activity was tested for the oxidation of carbon monoxide. The target of this work was to evaluate the effects of (1) the crystallinity of the TiO shell and (2) the presence of titanate phases. Transmission electron microscopy and X-ray diffraction data show that increasing calcination temperatures, from 850 to 1250 K, leads to the formation of larger titania crystallites. These crystallites are typically in the form of anatase, but some rutile is also made at high temperatures. The general yolk-shell nanostructures retain their basic characteristics upon calcination and upon treatment with HCl (used to remove the titanate phases), but a few structural and chemical changes do take place: (1) the void-space diameter is reduced by approximately 10% when going from T = 850 K to T = 1250 K, a change that is accompanied by a decrease in the surface area (estimated from N adsorption-desorption isotherms); (2) the shell thickness remains unaffected by either calcination or HCl treatment; (3) the pore volume also remains approximately constant with increasing calcination temperature in the catalysts free of titanates but diminishes significantly in the samples with titanate phases; (4) the mesoporosity is minimal in all yolk-shell nanostructures but more noticeable with the pure TiO shells; (5) the titanates have high Na content (measured by X-ray photoelectron spectroscopy), but that Na is fully removed upon treatment with HCl; (6) no Ti was detectable in any of the samples, but silica, together with C and (minor amounts of) N, was present in all; (7) all Au is in metallic form; (8) two temperature regimes were observed for the catalytic oxidation of CO, as reported for other similar samples in the past, an Arrhenius regime around or above room temperature, and a cryogenic range going to temperatures as low as 120 K; (9) the latter regime is only seen with the samples containing titanate phases; (10) the titanates seem to also aid in the oxidation at higher temperatures; and (11) in general, increasing titania crystallinity leads to a decrease the catalytic activity.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1063/1.5132715 | DOI Listing |
ACS Nano
January 2025
Department of Materials Science and Engineering, Drexel University, Philadelphia, Pennsylvania 19104, United States.
Recently, we reported on the simple, scalable synthesis of quantum-confined one-dimensional (1D) lepidocrocite titanate nanofilaments (1DLs). Herein, we show, using solid-state UV-vis spectroscopy, that reducing the concentration of aqueous 1DL colloidal suspensions from 40 to 0.01 g/L increases the band gap energy and light absorption onset of dried filtered films from ≈3.
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083, China.
Porous piezoelectric materials have attracted much interest in the fields of sensing and energy harvesting owing to their low dielectric constant, high piezoelectric voltage coefficient, and energy harvesting figure of merit. However, the introduction of porosity can decrease the piezoelectric coefficient, which restricts the enhancement of output current and power density. Herein, to overcome these challenges, an array-structured piezoelectric composite energy harvester with aligned porosity was constructed via a dual structure design strategy to enhance the output current and power density.
View Article and Find Full Text PDFSmall
January 2025
Shandong Provincial Key Laboratory of Molecular Engineering, School of Chemistry and Chemical Engineering, Qilu University of Technology (Shandong Academy of Sciences), Jinan, Shandong, 250353, P. R. China.
Oxygen vacancy (OV) defect engineering plays a crucial role in enhancing photocatalytic efficiency. However, the direct visual characterization of oxygen vacancies still remains technically limited. Herein, a bismuth titanate (BiTiO, BTO-OV) model photocatalyst containing oxygen vacancies is constructed through density functional theory (DFT) calculations to reveal the influence mechanism of distinctive periodic quantum well and oxygen vacancies on the charge transfer behavior in BTO.
View Article and Find Full Text PDFScaffolds are of great interest in tissue engineering associated with regenerative medicine owing to their ability to mimic biological structures and provide support for new tissue formation. Several techniques are used to produce biological scaffolds; among them, far-field electrospinning (FFES) process is widely used due to its versatility in producing promising structures similar to native tissues owing to the electrospun nanofibers. On the other hand, near-field electrospinning (NFES) has been investigated due to the possibility of creating scaffolds with suitable architecture for their use in specific biological tissues.
View Article and Find Full Text PDFMaterials (Basel)
November 2024
Center of Physics of Minho and Porto Universities (CF-UM-UP), Laboratory for Materials and Emergent Technologies (LaPMET), Departamento de Física, Universidade do Minho, Campus de Gualtar, 4710-057 Braga, Portugal.
Laser ablation was used to successfully fabricate multiferroic bilayer thin films, composed of BaTiO (BTO) and CoFeO (CFO), on highly doped (100) Si substrates. This study investigates the influence of BaTiO layer thickness (50-220 nm) on the films' structural, magnetic, and dielectric properties. The dense, polycrystalline films exhibited a tetragonal BaTiO phase and a cubic spinel CoFeO layer.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!