Introduction: Mucopolysaccharidoses (MPS) are rare and clinically heterogeneous lysosomal storage disorders. Carpal tunnel syndrome (CTS) is a frequent complication in MPS types I, II, VI, and VII. CTS symptoms are difficult to recognize in these children, and often there is a lack of appropriate investigations.
Patients And Methods: In this retrospective study, all MPS patients were referred to the electrodiagnostic (EDX) laboratory of a single academic center during a 10-year period. Forty-eight children underwent serial EDX studies for CTS diagnosis and follow-up after surgery. Forty-two patients were diagnosed with CTS. Sensory nerve conduction velocity (SNCV), distal motor latency (DML), and motor nerve conduction velocity through the wrist (MNCV-W) of the median nerve were reviewed and analyzed.
Results: One-hundred-three EDX examinations were performed on 48 patients. The median age at disease diagnosis was 2.1 years versus 4.9 years for CTS diagnosis. Analysis of the series revealed that electrophysiological abnormalities of CTS could have started much earlier (before the age of 2 years or at diagnosis of MPS). Diagnosis was based on SNCV and DML results, and MNCV-W was taken into consideration. Bilateral CTS was frequent (88%) in the types of MPS studied in our population and was observed from the first year of life, and may not have be associated with obvious clinical symptoms. EDX studies also helped in the follow-up and detection of CTS relapses, thus leading to an early intervention allowing a better recovery.
Conclusion: EDX studies should be performed promptly and regularly in these patients. Prospective studies are required in order to understand the effect of disease-specific therapies in preventing the development of CTS in these patients.
Synopsis: EDX studies should be performed in MPS patients soon after diagnosis and during routine follow-up, before and after surgical decompression.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC7169406 | PMC |
| http://dx.doi.org/10.3390/diagnostics10010005 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Towards the photodeposition of SiGe-type materials oligomers of cyclogermapentenes and cyclosilapentenes.
Dalton Trans
January 2025
Department of Chemistry, University of Alberta, 11227 Saskatchewan Dr, Edmonton, Alberta, T6G 2G2, Canada.
This article provides an alternative pathway towards cyclosilapentenes (, SiH2-iPr and SpiroSi) involving the use of Rieke magnesium to activate the requisite dienes for synthesis. Subsequent metal-mediated dehydrocoupling of cyclosilapentene and mixtures with another cyclogermapentene gives oligomers with backbone Si-Si (number average molecular weight, = 1.0 kDa) and Si-Ge ( = 1.
View Article and Find Full Text PDFImpact of climate change that stems from gaseous emissions require sustainable materials to eliminate sulfur. This study involves the modification of humic acid with magnetite nanoparticles (Fe₃O₄ NPs) by a microwave-assisted synthesis of an absorbent with reasonable pore volume and diameter for elimination of thiophenic compounds from fuel. The magnetic nano adsorbent designated Fe3O4@HA was characterized using advanced spectroscopic techniques, while their structure and morphology were analyzed through DLS, XPS, XRD, FT-IR, TGA, FESEM-EDX, VSM, and BET-N2 techniques.
View Article and Find Full Text PDFNi-Mo nanostructure alloys as effective electrocatalysts for green hydrogen production in an acidic medium.
RSC Adv
January 2025
Department of Chemistry, Faculty of Science, Suez Canal University Ismailia 41522 Egypt +201113343594.
Achieving a net-zero emissions economy requires significant decarbonization of the transportation sector, which depends on the development of highly efficient electrocatalysts. Electrolytic water splitting is a promising approach to this end, with Ni-Mo alloys emerging as strong candidates for hydrogen production catalysts. This study investigates the electrodeposition of Ni and Ni-Mo nanostructured alloys with high molybdenum content onto low-carbon steel cathodes using a novel alkaline green lactate bath.
View Article and Find Full Text PDFFabrication and characterization of 3D-printed polymeric-based scaffold coated with bioceramic and naringin for a potential use in dental pulp regeneration (in vitro study).
Int Endod J
January 2025
Restorative and Aesthetic Dentistry Department, College of Dentistry, University of Baghdad, Baghdad, Iraq.
Aim: 3D-printed scaffolds loaded with healing directed agents could be employed for better treatment outcome in regenerative dentistry. The aim of this study was to fabricate and characterize simple 3D-printed poly lactic acid (PLA) scaffolds coated with nanoHydroxyapatite (nHA), Naringin (NAR), or their combination, and testing their morphological, chemical, mechanical, antibacterial, biocompatible and bioactive properties.
Methodology: Two variants pore sizes, 300 and 700 μm, of 3D-printed PLA disc scaffolds measuring (10 × 1 mm) were fabricated.
Isolation, structural characterization of (1 → 4), (1 → 6)-α-D-glucan from Dioscorea Alata and synthesis and catalytic activity studies of (1 → 4), (1 → 6)-α-D-glucan derived carbon dots.
Carbohydr Res
January 2025
Department of Chemistry (UG and PG), Midnapore College (Autonomous), Midnapore, 721101, India. Electronic address:
Herein, a straightforward, productive protocol was adopted for the synthesis of carbon dots (CDs) by a simple microwave-assisted technique from (1 → 4), (1 → 6)-α-D-glucan polysaccharide (DAPS). The isolation and structural characterization of (1 → 4), (1 → 6)-α-D-glucan from the aqueous extracting of the Diascorea Alata was described here. The photo-physical and morphological studies of the prepared high quantum yield (27.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!