Background: Accurate assessment of hepatic fibrosis in patients with chronic HBeAg-negative Hepatitis B is of crucial importance not only to predict the long-term clinical course, but also to evaluate antiviral therapy indication. The aim of this study was to prospectively assess the utility of point shear wave elastography (pSWE) for longitudinal non-invasive fibrosis assessment in a large cohort of untreated patients with chronic HBeAg-negative hepatitis B virus (HBV) infection.
Methods: 407 consecutive patients with HBeAg-negative HBV infection who underwent pSWE, transient elastography (TE) as well as laboratory fibrosis markers, including fibrosis index based on four factors (FIB-4), aspartate to platelet ratio index (APRI) and FibroTest, on the same day were prospectively followed up for six years. Patients were classified into one of the three groups: inactive carriers (IC; HBV-DNA <2000 IU/mL and ALT <40 U/L); grey zone group 1 (GZ-1; HBV DNA <2000 IU/mL and ALT >40 U/L); grey zone group 2 (GZ-2; HBV-DNA >2000 IU/mL and ALT <40 U/L).
Results: pSWE results were significantly correlated with TE (r = 0.29, < 0.001) and APRI (r = 0.17; = 0.005). Median pSWE values did not differ between IC, GZ-1 and GZ-2 patients ( = 0.82, = 0.17, = 0.34). During six years of follow-up, median pSWE and TE values did not differ significantly over time (TE: = 0.27; pSWE: = 0.05).
Conclusion: Our data indicate that pSWE could be useful for non-invasive fibrosis assessment and follow-up in patients with HBeAg-negative chronic HBV infection.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6947378 | PMC |
http://dx.doi.org/10.3390/jcm8122101 | DOI Listing |
Nanotechnology
January 2025
Universiti Teknologi PETRONAS, Centre of Innovative Nanostructures and Nanodevices (COINN), Universiti Teknologi PETRONAS, 32610 Seri Iskandar, Perak Darul Ridzuan, MALAYSIA, Seri Iskandar, Perak, 32610, MALAYSIA.
Most previously reported susceptors for microwave welding are in powder form. In this study, a thin-film susceptor was employed due to its uniform heating rate and ease of handling. Silicon carbide nanowhisker (SiCNW) were incorporated into a poly(methyl methacrylate) (PMMA) matrix to create a nanocomposite thin film, which served as the susceptor.
View Article and Find Full Text PDFVasa
January 2025
Faculty of Medicine, University of Oslo, Norway.
Intermittent negative pressure is an emerging treatment for lower limb vascular disease but the specific physiological effects, particularly upon large artery haemodynamics are unclear. This study examined the influence of intermittent negative pressure upon popliteal artery shear rate during both supine and sitting postures. Eleven healthy participants (5 female; age: 28.
View Article and Find Full Text PDFMicromachines (Basel)
December 2024
School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo 454000, China.
This article conducts wire bonding tests and cold/hot-cycle tests using φ 0.025 mm Ag-Au alloy wires and Ag-Au-Pd alloy wires with different specifications. The results show that, due to the addition of the alloying element Pd, under the same bonding parameters, the fracture strength and ball-bonded point shear force of the Ag-Au-Pd alloy wires are significantly higher than those of the Ag-Au alloy wires.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
School of & Architecture & Architectural Engineering, Hanyang University ERICA, Ansan 15588, Republic of Korea.
This study conducted experiments to investigate the flexural behavior of steel-concrete composite beams with U-shaped sections, utilizing cold-formed lipped channels as web components. To enhance both flexural and shear performance, trapezoidal plates were added to the lower sides of the composite beams. A total of ten specimens were fabricated, with variables defined according to the following criteria: presence of bottom tension reinforcement and bottom studs, thickness of the trapezoidal side plates (6 mm and 8 mm), and the welding method.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Hunan Province Engineering Research Center for High Thermal Conductivity Metal-Matrix Composites, Hunan Harvest Technology Development Co., Changsha 410219, China.
Spark plasma sintering (SPS) is an effective technique for studying the diffusion bonding of diamond/Cu composites, and has the potential to advance the application of copper matrix composites. This study investigates the SPS diffusion bonding of diamond/Cu composites using a chromium (Cr) interlayer. The effects of process parameters on the microstructure and mechanical properties of the bonding interface were evaluated through shear strength testing and SEM analysis.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!