The aim of this work was to demonstrate an optimization methodology to reliably obtain stable macrodispersions (i.e., for ≥24 h) of carbon nanotubes in water using sonication. Response surface methodology (RSM) was utilized to assess and optimize the sonication parameters for the process. The studied input parameters were (i) sonication time (duration), (ii) amplitude (of vibration), and (iii) pulse-on/off (duration) of the sonicator. The analyzed responses were mean diameter and size distribution of multiwalled carbon nanotube (MWNT) aggregates in water, which were measured by the dynamic light scattering technique. A semiempirical model was developed and statistically tested to estimate the magnitude of sonicator parameters required to obtain specified MWNT macrodispersions (i.e., aggregates' mean diameter and distribution) in water. The results showed that MWNT aggregates of 2 ± 0.5 μm can be obtained by optimizing sonicator parameters to a sonication time of 89 s, amplitude of 144 μm, and pulse-on/off cycle of 44/30 s. These process settings for 100 mg/L MWNTs in a 30 mL aliquot of deionized water would consume 863 J/mL of sonication energy. Contrary to the popular belief, "sonication time" and/or "sonication energy input" were not found to be proportional to the degree of dispersion of MWNTs in water. This might be the reason for the frequent disparity and nonreproducibility of sonication results reported in scientific literature, especially for dispersing nanomaterials in a number of different systems. The amplitude of vibration was noted to be the most sensitive parameter affecting MWNT aggregates' diameter and distribution in water. The characterization of MWNTs was performed using electron microscopy, surface area analyzer, thermogravimetric analyzer, and zeta potential analyzer. This study can be helpful in evaluating sonication dispersion of particulate matter in other incompressible fluids such as graphene dispersion in organic solvents.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6648579 | PMC |
| http://dx.doi.org/10.1021/acsomega.8b02965 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Strength and Poisson's ratio of fused filament fabrication parts made from carbon filler enhanced PEEK compounds at elevated temperatures.
Sci Rep
December 2024
School of Electrical Engineering, Aalto University, P.O. Box 15500, Aalto, FI-00076, Finland.
Engineering plastics are finding widespread applications across a broad temperature spectrum, with additive manufacturing (AM) having now become commonplace for producing aerospace-grade components from polymers. However, there is limited data available on the behavior of plastic AM parts exposed to elevated temperatures. This study focuses on investigating the tensile strength, tensile modulus and Poisson's ratio of parts manufactured using fused filament fabrication (FFF) and polyetheretherketone (PEEK) plastics doped with two additives: short carbon fibers (SCFs) and multi-wall carbon nanotubes (MWCNTs).
View Article and Find Full Text PDFA Janus Separator Regulating Zinc Deposition Behavior Synergistically by Cellulose and ZrO Nanoparticles Toward High-Performance Aqueous Zinc-Ion Batteries.
Small
December 2024
Songshan Lake Materials Laboratory (SLAB), Dongguan, 523808, P. R. China.
Aqueous zinc-ion batteries (AZIBs) stand out among many energy storage systems due to their many merits, and it's expected to become an alternative to the prevailing alkali metal ion batteries. Nevertheless, the cumbersome manufacturing process and the high cost of conventional separators make them unfavorable for large-scale applications. Herein, inspired by the unique nature of cellulose and ZrO, a Janus cellulose fiber (CF)/polyvinyl alcohol (PVA)/ZrO separator is prepared via the vacuum filtration method.
View Article and Find Full Text PDFFacile Preparation of Carbon Nanotube-Based Skin-Like Pressure Sensors.
Small
December 2024
Department of Chemistry & Chemical Biology and the Brockhouse Institute for Materials Research, McMaster University, 1280 Main St. W., Hamilton, ON, L8S 4M1, Canada.
Flexible sensors have garnered significant interest for their potential to monitor human activities and provide valuable feedback for healthcare purposes. Single-walled carbon nanotubes (SWNTs) are promising materials for these applications but suffer from issues of poor purity and solubility. Dispersing SWNTs with conjugated polymers (CPs) enhances solution processability, yet the polymer sidechains can insulate the SWNTs, limiting the sensor's operating voltage.
View Article and Find Full Text PDFResolving the Kinetics of Single-Walled Carbon Nanotube-Polyester Polyurethane Nanoparticle Conjugate Fluorescence Sensors toward Polymer Degrading Enzymes.
Nano Lett
December 2024
Department of Chemical and Biological Engineering, Iowa State University, Ames, Iowa 50011, United States.
Single-walled carbon nanotubes (SWCNTs) are fluorescent materials that have been developed as sensors for measuring the activities of enzymes. However, most sensors to date rely on end-point measurement and empirical functions to correlate enzyme concentrations with fluorescence responses. Less emphasis is put on analyzing time-dependent fluorescence responses and their connections with enzymatic kinetics.
View Article and Find Full Text PDFAntimicrobial Efficacy of Single-Walled Carbon Nanotubes and Their Combinations Against Enterococcus faecalis Assessed Using the Agar Diffusion Method: An In Vitro Study.
Cureus
November 2024
Department of Conservative Dentistry and Endodontics, SRM Kattankulathur Dental College, Chennai, IND.
Introduction: This study aimed to evaluate the antimicrobial efficacy of single-walled carbon nanotubes when combined with the commonly used intracanal medicaments by checking their zone of inhibition against .
Materials And Methods: The test materials were divided into five different groups, namely, Group I: single-walled carbon nanotubes; Group II: calcium hydroxide; Group III: chlorhexidine; Group IV: single-walled carbon nanotubes + calcium hydroxide; and Group V: single-walled carbon nanotubes + chlorhexidine. Five sterile Petri plates per group were inoculated with (); wells were made in the plates, one on each side, and a volume of 50 microliters of each solution was dispensed into individual wells using a pipette.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!