Inertial cavitation-based sonoporation has been utilized to enhance treatment delivery efficacy. In our previous study, we demonstrated that tumor therapeutic efficacy can be enhanced through vaporization-assisted sonoporation with gold nanodroplets (AuNDs). Specifically, the AuNDs were vaporized both acoustically (i.e., acoustic droplet vaporization, ADV) and optically (i.e., optical droplet vaporization, ODV). A continuous wave (CW) laser was used for ODV in combination with an ultrasound pulse for ADV. Although effective for vaporization, the use of a CW laser is not energy efficient and may create unwanted heating and concomitant tissue damage. In this study, we propose the use of a pulsed wave (PW) laser to replace the CW laser. In addition, the PW laser was applied at the rarefaction phase of the ultrasound pulse so that the synergistic effects of ADV and ODV can be expected. Therefore, a significantly lower laser average power can be expected to achieve the vaporization threshold. Compared to the CW laser power at 2 W/cm from the previous approach, the PW laser power was reduced to only 0.2404 W/cm. Furthermore, we also demonstrate in vitro that the sonoporation rate was increased when the PW laser was applied at the rarefaction phase. Specifically, the vaporization signal, the inertial cavitation signal, and the sonoporation rate all displayed a 1-µs period, which corresponded to the period of the 1-MHz acoustic wave used for ADV, as a function of the relative laser delay. The increased sonoporation rate indicates that this technique has the potential to enhance sonoporation-directed drug delivery and tumor therapy with a lower laser power while keeping the cell death rate at the minimum. Photoacoustic imaging can also be performed at the same time since a PW laser is used for the ODV.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6631315 | PMC |
http://dx.doi.org/10.3390/pharmaceutics11060279 | DOI Listing |
Adv Mater
January 2025
Sustainability Institute, The Ohio State University, Columbus, OH, 43210, USA.
Nature provides many examples of the benefits of nanoscopic surface structures in areas of adhesion and antifouling. Herein, the design, fabrication, and characterization of liquid crystal elastomer (LCE) films are presented with nanowire surface structures that exhibit tunable stimuli-responsive deformations and enhanced adhesion properties. The LCE films are shown to curl toward the side with the nanowires when stimulated by heat or organic solvent vapors.
View Article and Find Full Text PDFSmall Methods
January 2025
Department of Chemistry and Bioengineering, Graduate School of Engineering, Osaka Metropolitan University, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka, 558-8585, Japan.
A patterned growth of crystals of 1,2-bis(2,5-dimethyl-3-thienyl)perfluorocyclopentene (1a) on the glass substrate with convex guides is reported by sublimation methods. The lower supersaturation of substrate surfaces with higher temperatures can facilitate the vapor-to-liquid process rather than the vapor-to-crystal process in the early stage of the sublimation. Micro-droplets of melts of 1a are generated on the sidewalls of the convex guides, then crystallized into the microcrystals, accompanied by the rearrangements of the crystallographic in-plane orientations.
View Article and Find Full Text PDFJ Hazard Mater
January 2025
Center for Disease Control and Prevention of People's Liberation Army, Beijing 100071, China.
Peracetic acid (PAA) is an emerging disinfectant known to be highly effective against various microorganisms. However, the capability of PAA to eliminate spores under different conditions and its application in liquid and gaseous forms remain unclear. Here, we aimed to develop a stabilized single-composite PAA and evaluate its disinfection efficacy in both liquid and gaseous form against suspended or surface-coated spores under varying temperature and humidity conditions.
View Article and Find Full Text PDFACS Nano
January 2025
Center for Functional Nanomaterials, Brookhaven National Laboratory, Upton, New York 11973, United States.
With their ability to self-assemble spontaneously into well-defined nanoscale morphologies, block copolymer (BCP) thin films are a versatile platform to fabricate functional nanomaterials. An important challenge to wider deployment of BCPs in nanofabrication is combining precise control over the nanoscale domain orientation in BCP assemblies with scalable deposition techniques that are applicable to large-area, curved, and flexible substrates. Here, we show that spray-deposited smooth films of a nominally disordered BCP exhibit latent orientations, which can be prescriptively selected by controlling solvent evaporation during spray casting.
View Article and Find Full Text PDFLangmuir
January 2025
Department of Chemical and Pharmaceutical Engineering, Faculty of Chemistry and Pharmacy, Sofia University, 1 James Bourchier Avenue, Sofia 1164, Bulgaria.
Spontaneous bubble growths in liquids are usually triggered by rapid changes in pressure or temperature that can lead to liquid gas supersaturation. Here, we report alternative scenarios of the spontaneous growths of bubbles inside a high-saturation-vapor-pressure and high-air-solubility perfluorocarbon liquid (PP1) that were observed under ambient quiescent conditions. First, we investigate spontaneous bubble growth inside the single PP1 phase, which was left to evaporate freely.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!