Laser-based additive manufacturing processes are increasingly used for fabricating components made of nickel-based superalloys. The microstructure development, and in particular the precipitation of secondary phases, is of great importance for the properties of additively manufactured nickel-based superalloys. This paper summarizes the literature data on the microstructure of Inconel 625 superalloy manufactured using laser-based powder-bed fusion and directed energy deposition processes, with particular emphasis on the phase identification of precipitates. The microstructure of Inconel 625 manufactured by laser-based directed energy deposition in as-built condition is investigated by means of light microscopy and transmission electron microscopy. Phase analysis of precipitates is performed by the combination of selected area electron diffraction and microanalysis of chemical composition. Precipitates present in the interdendritic areas of as-built Inconel 625 are identified as MC and MC₆ carbides as well as the Laves phase.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6480167 | PMC |
| http://dx.doi.org/10.3390/ma12071144 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Application of Powder-Bed Fusion of Metals Using a Laser for Manufacturing of M300 Maraging Steel Tools Intended for Sheet Metal Bending.
Materials (Basel)
December 2024
Faculty of Materials Science and Engineering, Warsaw University of Technology, Woloska 141, 02-507 Warsaw, Poland.
This paper presents the results of a pilot application of Powder-Bed Fusion of Metals Using a Laser (PBF-LB/M) for the fabrication of M300 (1.2709) maraging steel sheet metal bending tools. S235 steel was used as a substrate for the fabrication of bending punches.
View Article and Find Full Text PDFOptimization of Turning of Inconel 625 to Improve Surface Quality After Finishing Process.
Materials (Basel)
December 2024
Department of Production Engineering, Faculty of Mechanical, Cracow University of Technology, 31-155 Cracow, Poland.
The process of machining the modern engineering materials, such as nickel-based superalloys, still requires improvement. This paper focuses on comparing the turning process of Inconel 625 superalloy using three types of cutting inserts to obtain the finishing process. The influence of cutting data, such as cutting speed, feed rate, and cutting depth, on the machined surface quality, surface quality were selected.
View Article and Find Full Text PDFMicrostructure, Hardness and High-Temperature Corrosion Behaviors in Sulfur-Containing Environment of Laser Cladding YO/IN625 Composite Coating.
Materials (Basel)
September 2024
School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049, China.
Water-cooled wall tubes are susceptible to high-temperature corrosion during service. Applying high-performance coatings via laser cladding on the tube surfaces can significantly enhance corrosion resistance and extend the service life of the tubes, providing substantial economic advantages. This paper prepared YO/IN625 composite coating by means of high-speed laser cladding.
View Article and Find Full Text PDFAccurately Measuring the Infrared Spectral Emissivity of Inconel 601, Inconel 625, and Inconel 718 Alloys during the Oxidation Process.
Sensors (Basel)
September 2024
Henan Key Laboratory of Infrared Spectrum Measures and Applications, School of Physics, Henan Normal University, Xinxiang 453007, China.
Accurate measurement of the infrared spectral emissivity of nickel-based alloys is significant for applications in aerospace. The low thermal conductivity of these alloys limits the accuracy of direct emissivity measurement, especially during the oxidation process. To improve measurement accuracy, a surface temperature correction method based on two thermocouples was proposed to eliminate the effect of thermal conductivity changes on emissivity measurement.
View Article and Find Full Text PDFMicrostructural Stability of IN625 Reinforced by the Addition of TiC Produced by Laser Powder Bed Fusion after Prolonged Thermal Exposure.
Materials (Basel)
September 2024
DISAT-Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy.
This paper deals with the development and characterization of an Inconel 625 (IN625) reinforced with 2 wt.% of sub-micrometrical TiC particles produced by the laser powder bed fusion (LPBF) process. IN625 and IN625 2 wt.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!