One of the fundamental issues in the Fused Filament Fabrication (FFF) additive manufacturing process lies in the mechanical property anisotropy where the strength of the FFF-3D printed part in the build-direction can be significantly lower than that in other directions. The physical phenomenon that governs this issue is the coupled effect of macroscopic thermal mechanical issues associated with the thermal history of the interface, and the microscopic effect of the polymer microstructure and mass transfer across interfaces. In this study it was found that the use of 34.4 kHz ultrasonic vibrations during FFF-3D printing results in an increase of up to 10% in the interlayer adhesion in Acrylonitrile Butadiene Styrene (ABS), comparing the printing in identical thermal conditions to that in conventional FFF printing. This increase in the interlayer adhesion strength is attributed to the increase in polymer reptation due to ultrasonic vibration-induced relaxation of the polymer chains from secondary interactions in the interface regions.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6419166 | PMC |
| http://dx.doi.org/10.3390/polym11020315 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Advancing Structural Reinforcement in 3D-Printed Concrete: Current Methods, Challenges, and Innovations.
Materials (Basel)
January 2025
College of Water Conservancy, Shenyang Agricultural University, Shenyang 110866, China.
With rapid global urbanization and economic development, 3D concrete printing (3DCP) technology has emerged as an innovative construction method, garnering increasing attention and application. Compared to traditional construction techniques, 3DCP not only reduces resource waste and carbon emissions during the building process but also significantly enhances construction efficiency, demonstrating considerable potential in the construction industry. As 3DCP advances from theoretical studies to real-world applications, providing stable and reliable structural reinforcement solutions becomes essential.
View Article and Find Full Text PDFCatechol redox maintenance in mussel adhesion.
Nat Rev Chem
January 2025
Department of Chemistry & Biochemistry, University of California Santa Barbara, Santa Barbara, CA, USA.
Catechol-functionalized proteins in mussel holdfasts are essential for underwater adhesion and cohesion and have inspired countless synthetic polymeric materials and devices. However, as catechols are prone to oxidation, long-term performance and stability of these inventions awaits effective antioxidation strategies. In mussels, catechol-mediated interactions are stabilized by 'built-in' homeostatic redox reservoirs that restore catechols oxidized to quinones.
View Article and Find Full Text PDFMulti-Parametric Optimization of 3D-Printed Components.
Polymers (Basel)
December 2024
CESTER-Research Center for Industrial Robots Simulation and Testing, Technical University of Cluj-Napoca, 400114 Cluj-Napoca, Romania.
This study explores the experimental and theoretical optimization of process parameters to improve the quality of 3D-printed parts produced using the Fused Deposition Modeling technique. To ensure the cost-effective production of high-quality components, advancements in printing strategies are essential. This research identifies optimal 3D printing strategies to enhance the quality of finished products.
View Article and Find Full Text PDFConfined CVD Synthesis and Temperature-Dependent Spectroscopic Properties of Bilayer Graphene Ribbon Arrays with Bifunctional Modulation of Adhesion Metal.
Small Methods
January 2025
School of Chemistry and Chemical Engineering, Chongqing University, Chongqing, 401331, China.
Bilayer graphene ribbons (GRs) hold great promise for the fabrication of next-generation nanodevices, thanks to unparalleled electronic properties, especially the tunable bandgap in association with twist angle, ribbon width, edge structure, and interlayer coupling. A common challenge in manufacturing bilayer GRs via templated chemical vapor deposition (CVD) approach is uncontrollable dewetting of micro- and nano-scaled patterned metal substrates. Herein, a confined CVD synthetic strategy of bilayer GR arrays is proposed, by utilizing the bifunctional Ni as a buffered adhesion layer to regulate the anisotropic dewetting of metal film in the V-groove and as a carbon-dissolution regulated metal to initiate the bilayer nucleation.
View Article and Find Full Text PDFBreaking the Trade-Off Between Electrical Conductivity and Mechanical Strength in Bulk Graphite Using Metal-Organic Framework-Derived Precursors.
Adv Sci (Weinh)
January 2025
State Key Laboratory for Modification of Chemical Fibers and Polymer Materials & College of Materials Science and Engineering, Donghua University, Shanghai, 201620, China.
High-performance bulk graphite (HPBG) that simultaneously integrates superior electrical conductivity and excellent strength is in high demand, yet it remains critical and challenging. Herein a novel approach is introduced utilizing MOF-derived nanoporous metal/carbon composites as precursors to circumvent this traditional trade-off. The resulting bulk graphite, composed of densely packed multilayered graphene sheets functionalized with diverse cobalt forms (nanoparticles, single atoms, and clusters), exhibits unprecedented electrical conductivity in all directions (in-plane: 7311 S cm⁻¹, out-of-plane: 5541 S cm⁻¹) and excellent mechanical strength (flexural: 101.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!