This paper discusses the issue of controlling the epitaxial growth of mixed group V alloys to form a type-I InGaAsSb/AlGaAsSb double quantum wells (QWs) structure. We also discuss the run-to-run reproducibility of lattice-matched AlGaAsSb alloys and strained InGaAsSb in terms of growth parameters (V/III ratio, Sb₂/As₂ ratio). Molecular beam epitaxy (MBE) was used to grow two type-I InGaAsSb double-QWs laser structures differing only in the composition of the bottom cladding layer: AlGaAsSb (sample A) and AlGaAsSb (sample B). Both samples were respectively used in the fabrication of photonic crystal surface-emitting lasers (PCSELs). Sample A presented surface lasing action from circular as well as triangular photonic crystals. Sample B did not present surface lasing due to the deterioration of the active region during the growth of the upper cladding. Our findings underline the importance of temperature in the epitaxial formation of AlGaAsSb in terms of lasing performance.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6357140 | PMC |
| http://dx.doi.org/10.3390/ma12020317 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effect of Hole Shift on Threshold Characteristics of GaSb-Based Double-Hole Photonic-Crystal Surface-Emitting Lasers.
Micromachines (Basel)
April 2021
Institute of Electronics, National Yang Ming Chiao Tung University, Hsinchu City 30010, Taiwan.
Photonic-crystal (PC) surface-emitting lasers (SELs) with double-hole structure in the square-lattice unit cell were fabricated on GaSb-based type-I InGaAsSb/AlGaAsSb heterostructures. The relative shift of two holes was varied within one half of the lattice period. We measured the lasing wavelengths and threshold pumping densities of 16 PC-SELs and investigated their dependence on the double-hole shift.
View Article and Find Full Text PDFPCSEL Performance of Type-I InGaAsSb Double-QWs Laser Structure Prepared by MBE.
Materials (Basel)
January 2019
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, Hsinchu 300, Taiwan.
This paper discusses the issue of controlling the epitaxial growth of mixed group V alloys to form a type-I InGaAsSb/AlGaAsSb double quantum wells (QWs) structure. We also discuss the run-to-run reproducibility of lattice-matched AlGaAsSb alloys and strained InGaAsSb in terms of growth parameters (V/III ratio, Sb₂/As₂ ratio). Molecular beam epitaxy (MBE) was used to grow two type-I InGaAsSb double-QWs laser structures differing only in the composition of the bottom cladding layer: AlGaAsSb (sample A) and AlGaAsSb (sample B).
View Article and Find Full Text PDFWe demonstrated for the first time above room temperature (RT) GaSb-based mid-infrared photonic crystal surface emitting lasers (PCSELs). The lasers, under optical pumping, emitted at λ(lasing)~2.3μm, had a temperature insensitive line width of 0.
View Article and Find Full Text PDFIn this study, the optical properties of InAs quantum dots (QDs) with various strain-reducing layers (SRLs) of GaAsSb and InGaAsSb are characterized using photoluminescence (PL) and time-resolved PL (TRPL) measurements. The room-temperature PL results for the InAs/InGaAsSb QDs revealed stronger emission intensities than InAs QDs capped with an GaAs(1-x)Sb(x) (x = 20%)SRL, although both samples were grown under the same Sb flux during the molecular beam epitaxy process. The InAs/InGaAsSb QDs showed a significant elongation of emission wavelengths to 1450 and 1310 nm for the ground and first-excited state at room temperature.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!