Background And Aim: The objective of this study was to describe the manual fabrication of a transparent facial pressure mask for treating facial deformities. The mask combines the use of a silicone inner liner and mechanical pressure in the facial region.
Technique: A negative mold is formed by covering the face with plaster. Manipulation of soft tissue is a crucial part in this process. After hardening and removal of the negative mold, the positive mold is formed and dried. Next a rolled silicone sheet is placed over the positive mold in a vacuum environment. Subsequently, the silicones are vulcanized. Then the rigid outside of the mask is created. The silicone inner liner and outside shell are then affixed.
Discussion: This described technique results in accurate facemasks with precise fitting. During therapy, the mask is adjusted multiple times to keep excellent fit, as remodeling of scars and deformities takes place.
Clinical Relevance: Facemasks are a reputable therapeutic modality to reduce excessive facial scarring. They require excellent fitting to give pleasing results. To provide a better understanding of facemask therapy, this study describes the manual fabrication technique.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6557004 | PMC |
| http://dx.doi.org/10.1177/0309364618820141 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
A tension system for angular correction of bent intramedullary nails: in vitro analysis.
Eur J Orthop Surg Traumatol
December 2024
Department of Orthopedics and Trauma, Universidade Federal Fluminense (UFF), Niterói, Rio de Janeiro, Brazil.
Purpose: Although several techniques have been described for bent intramedullary nail removal, there is no universally accepted strategy. We hypothesized that a device based on the action principle of a three-point bend fixture could facilitate extraction of bent intramedullary nails; this paper describes its design and experimental testing.
Methods: Five large synthetic left femurs and five steel intramedullary nails were used.
Sex-differences in the risk of carpal tunnel syndrome: results from a large Ontario, Canada worker cohort.
BMC Musculoskelet Disord
December 2024
Occupational Cancer Research Centre, Ontario Health, 525 University Avenue, 5th floor, Toronto, Ontario, M5G 2L3, Canada.
Background: Carpal tunnel syndrome (CTS) is a prevalent cumulative strain injury associated with occupational risk factors such as vibration, repetitive and forceful wrist movements, and awkward wrist postures. This study aimed to identify Ontario workers at elevated risk for CTS and to explore sex differences in CTS risk among workers.
Methods: The Occupational Disease Surveillance System (ODSS) links accepted lost time compensation claims to health administrative databases.
A sound approach for ova denudation.
F S Sci
December 2024
The Ronald O. Perelman and Claudia Cohen Center for Reproductive Medicine, Weill Cornell Medicine, New York, NY, 10021, USA. Electronic address:
Article Synopsis
- Developed a non-contact method using acousto-hydrodynamic tweezers (AHT) for denuding cumulus-oocyte complexes (COCs), showing higher efficiency compared to traditional manual methods.
- Tested on mice, the method demonstrated no damage to oocytes and reduced denudation time by 46% while maintaining embryo development rates.
- Findings suggest that using acoustic waves can significantly improve the denudation process for intracytoplasmic sperm injection (ICSI), potentially enhancing fertility treatment procedures.
A comparison of the accuracy and feasibility of a low-cost mobile application versus higher-cost handheld 3D scanner for digital ear prosthetics.
ANZ J Surg
December 2024
Royal Prince Alfred Institute of Academic Surgery, Sydney Local Health District, Sydney, New South Wales, Australia.
Background: Facial prosthetics are an important means to rehabilitate patients with congenital or acquired facial defects. However, with a time-consuming manual workflow and workforce shortage, access to facial prosthetics is limited in Australia and worldwide, especially for rural and remote patients. Optical 3D scanning has been increasingly integrated in digitizing data.
View Article and Find Full Text PDFA technique to enhance the gingival esthetics of a prototype complete arch fixed implant-supported prototype prosthesis using a 3D printed gingival veneer.
J Prosthet Dent
December 2024
Clinical Professor and Program Director, University of Connecticut Health Center, Farmington, Conn.; and Private practice, Glastonbury, Conn. Electronic address:
An important step in the workflow for a complete arch fixed implant-supported prosthesis is the fabrication of a prototype resin prosthesis to allow the patient to visualize the definitive treatment outcome and also to use as an interim prosthesis. Producing a prototype prosthesis with the natural appearance of the gingival color and contour has been challenging. Current methods include painted stains, manually applied pink composite resin or autopolymerizing acrylic resin, and multicolored resin blocks, but these are all relatively expensive, have less than optimal esthetics, and are labor-intensive and time-consuming.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!