Little is known about the wear rate of enamel and dentin opposing resin composite following restoration of the occlusal surface in patients with tooth wear. Hence, the aim of this in vitro study was to evaluate the wear of enamel and dentin surfaces when opposing each of three resin composites in a two-body and three-body wear test. The two-body and three-body wear of dentin, enamel, and three resin composites (Clearfil AP-X, Filtek Z250, and Filtek Supreme) opposing four antagonists (stainless steel and three resin composites) were evaluated using the ACTA wear machine. In addition, all the surfaces were evaluated with scanning electron microscopy. The results showed the lowest wear rate in enamel and the highest in dentine, with the composite showing intermediate wear rates. The three-body wear results were not affected by the antagonist and showed pure wear caused by the abrasive food medium. The in vitro enamel/composite wear ratio was 2.5. The results show that tooth wear accelerates as soon as enamel disappears and dentin is exposed to composite resin. Therefore, it is important to protect dentin with a restorative material.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/eos.12600 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Coating Agents for Resin Composites: Effect on Color Stability, Roughness, and Surface Micromorphology Subjected to Brushing Wear.
Oper Dent
January 2025
*Roberta Tarkany Basting, DDS, MSc, PhD, Professor, Restorative Dentistry Department, Faculdade São Leopoldo Mandic, São Paulo, Brazil.
This study evaluated the influence of six resin composite coating agents on color stability and surface roughness after toothbrushing abrasion. Discs (Ø6 mm x 2 mm) of nanofilled resin composite (Filtek Z350XT) were prepared for application of coating agents (n=10): control (absence), two surface sealants (PermaSeal and BisCover LV), two adhesive systems (Scotchbond Multi-Purpose Adhesive/3M Oral Care and Single Bond Universal), and two modeling liquids (Modeling Resin and Composite Wetting Resin). CIELab*, WID, and color change (ΔEab, ΔE00, and ΔWID) were analyzed at baseline, after finishing and polishing, after application of coating agents, after coffee staining (simulating 30 days and one year of staining), and after toothbrushing abrasion.
View Article and Find Full Text PDFProperties of New Partially Crystallized Lithium Disilicate CAD-CAM Materials.
Oper Dent
January 2025
*Kraig S. Vandewalle, DDS, MS, Col (ret), USAF, DC, Air Force Consultant in Dental Research Advanced Education in General Dentistry Residency, AF Postgraduate Dental School, Joint Base San Antonio - Lackland, TX, USA; Uniformed Services University of the Health Sciences, Bethesda, MD, USA.
Objective: The purpose of this study was to compare the optical, mechanical, and biological properties of two new, inexpensive lithium disilicate (LS2) materials (Lodden (LOD), LD Medical Technology; and BeautyZir (BZ), BeautyZir Technology) to a clinically established LS2 material (IPS e.max CAD (EMAX), Ivoclar Vivadent).
Methods And Materials: The optical properties of the translucency parameter (TP) and opalescence parameter (OP) were obtained with a dental spectrophotometer.
Microstructural Assessment of Molybdenum Disulfide Coatings Using Nanoindentation Hardness.
ACS Appl Mater Interfaces
January 2025
Material, Physical and Chemical Sciences Center, Sandia National Laboratories, Albuquerque, New Mexico 87123, United States.
MoS coatings are used extensively in aerospace and defense applications due to their ultralow friction and high wear resistance. Burnished and resin-bonded MoS coatings are commonly used in these applications due to simplicity in deposition and history of use, despite issues with consistency in coating properties and performance. Physical vapor deposition (PVD) of MoS thin films has emerged as a process alternative in the past 50 years, promising far greater control over film structure and composition but at a greater cost.
View Article and Find Full Text PDFClinical validity of fluorescence-based devices versus visual-tactile method in detection of secondary caries around resin composite restorations: diagnostic accuracy study.
BDJ Open
January 2025
Professor of Conservative Dentistry, Faculty of Dentistry, Cairo University, Giza, Egypt.
Objectives: To assess the validity of light-induced and laser-induced fluorescence devices compared to the visual-tactile method for detecting secondary caries around resin composite restorations.
Materials And Methods: The study included 20 participants with 30 resin-composite restored teeth. Restorations' margins were examined using three diagnostic methods: the visual-tactile method (FDI criteria), the light-induced fluorescence camera (VistaCam iX), and the laser-induced fluorescence device (DIAGNOdent pen), and the reference was visual inspection after removal of defective restorations.
Visible-Light-Fueled Polymerizations for 3D Printing.
Acc Chem Res
January 2025
Department of Chemistry, The University of Texas at Austin, 105 East 24th Street, Austin, Texas 78712, United States.
ConspectusLight-driven polymerizations and their application in 3D printing have revolutionized manufacturing across diverse sectors, from healthcare to fine arts. Despite the popularized notion that with 3D printing "imagination is the only limit", we and others in the scientific community have identified fundamental hurdles that restrict our capabilities in this space. Herein, we describe the group's efforts in developing photochemical systems that respond to nontraditional colors of light to elicit the rapid, spatiotemporally controlled formation of plastics.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!