Meniscal bearing dislocation while rolling over in sleep has never been reported in Oxford unicompartmental knee arthroplasty (UKA). This study reports two cases of meniscal bearing dislocation into the intercondylar ridge while rolling over in sleep. In the case of one patient, closed reduction of the bearing was performed, and the use of a knee brace was effective in preventing re-dislocation. In the second patient, closed reduction was possible; however, bearing dislocation was repeated. Therefore, revision surgery was performed by replacing the tibial component and using a thicker bearing. The common features in dislocation during rolling over while sleeping in both cases were dislocation into the intercondylar ridge, the combination of small femur and AA-size tibia components, and osteonecrosis. As determined by intraoperative testing, valgus position of the knee while rolling over in sleep could induce bearing dislocation into the intercondylar ridge. LEVEL OF EVIDENCE: Retrospective case series, Level IV.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.knee.2018.10.015DOI Listing

Publication Analysis

Top Keywords

bearing dislocation
20
rolling sleep
16
meniscal bearing
12
dislocation rolling
12
dislocation intercondylar
12
intercondylar ridge
12
unicompartmental knee
8
knee arthroplasty
8
patient closed
8
closed reduction
8

Similar Publications

Traumatic obturator dislocation of the hip associated with ipsilateral subtrochanteric femur fracture in a young adult: a case report.

J Med Case Rep

December 2024

Department of Internal Medicine, School of Medicine, College of Medicine and Health Science, University of Gondar, Gondar, Ethiopia.

Introduction: Traumatic obturator-type anterior dislocation of the hip with an ipsilateral subtrochanteric fracture is rarely encountered in clinical practice. This case presentation described a trauma patient with such a rare scenario.

Case Report: This paper reports a case of a 20-year-old Amhara ethnic male patient who had a traumatic anterior dislocation of the hip associated with an ipsilateral subtrochanteric femur fracture after a truck rolled over.

View Article and Find Full Text PDF

Objective: To compare the mid- and long-term effectiveness of patellar resurfacing versus non-resurfacing in primary total knee arthroplasty (TKA).

Methods: Twenty-six patients who underwent bilateral TKA between March 2013 and September 2015 were selected as the study subjects. One side was randomly chosen for patellar resurfacing (resurfacing group), and the other side was not (control group).

View Article and Find Full Text PDF

[Navigated and minimally invasive screw osteosynthesis of a talus fracture].

Unfallchirurgie (Heidelb)

December 2024

Klinik für Unfallchirurgie, Technische Universität München, Klinikum rechts der Isar, Ismaninger Straße 22, 81675, München, Deutschland.

Objective Of Surgery: The aim of this surgery is to safeguard the multifragmentary and nondisplaced talus fracture (body and neck) against secondary dislocation in a navigated and minimally invasive manner using screw osteosynthesis.

Indications: Due to the young age of the patient in the presented case and the risk of a possible secondary dislocation, the decision was made in favor of surgical treatment.

Contraindications: Soft tissue swelling, wound infections and allergies to the osteosynthesis material.

View Article and Find Full Text PDF

Talar neck fractures are complex injuries that become particularly challenging when accompanied by bone loss or comminution. This case report introduces the use of an allograft bone screw as a novel method for bridging lateral comminution at the talar neck, providing structural support and promoting bone regeneration. : A 20-year-old male sustained a comminuted talar neck fracture with subtalar and tibiotalar dislocation after a bouldering fall.

View Article and Find Full Text PDF

Nanograin enhanced surface layer strengthening of 3D printed intervertebral cage induced by sandblasting.

Biomed Mater

December 2024

Department of Orthopaedics, Fourth Military Medical University, No.1 Xinsi Road, Baqiao District, Xi'an, Shaanxi, 710032, CHINA.

3D printed customized titanium alloy (Ti6Al4V, TC4) as load-bearing prostheses and implants, such as intervertebral cage, were widely used in clinical practice. Natively biological inertia and inadequate bone in-growth of porous titanium alloy scaffolds hampered their clinically application efficiency and then extended healing period. To improve osseointegration capacity of 3D printed intervertebral cage, sandblasting was selected to execute their surface treatment.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!