This is an study composed by a fatigue test followed by an optical microscopy analysis. Dynamic abutments concept, recently introduced on screw-retained implant dental prosthesis, consists on the screw channel customisation according to the individual needs of each rehabilitation. Geometry and tightening torque differences advise the assessment of their mechanical performance. Clarify whether the combination of dynamic and conventional abutments in a three-unit implant-fixed prosthesis has detrimental effects either on the mechanical performance under cyclic loading or on the implant-abutment microgap dimensions. The fatigue test was performed in agreement with the ISO standard 14801. Then on the samples that resisted 5 million cycles, the implant-abutment microgap was measured on dynamic and conventional abutments using optical microscopy. Two unloaded samples were used as control group. The samples supported a load of 1050 N. The implant-abutment microgap measurement did not show statistically significant differences ( = .086) between loaded and unloaded groups, but the loaded conventional abutments showed a significant lower implant-abutment microgap ( = .05) than the loaded dynamic abutments. The combination of conventional and dynamic abutments do not seem to produce a decrease in fatigue resistance to a level below the mastication forces or an increase in the joint dimensions.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1080/03091902.2018.1520312 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Numerical investigation of coal pillar damage mechanisms for various width-to-height ratios.
Sci Rep
January 2025
School of Mines, China University of Mining and Technology, No.1 Daxue Rd, Xuzhou, 221116, China.
Pillar stability has garnered significant attention owing to the effects of pillars on coal resource recovery rate, coal pillar stability, and coal bump risk. This study examined the roadway stability control principles of conventional and yield coal pillars. The conventional coal pillars were designed as load-bearing structures with a high load-bearing capacity to carry most of the abutment load, while yield coal pillars were designed as buffer structures for transferring rapidly increasing abutment loads to adjacent solid coal ribs by progressive deformation.
View Article and Find Full Text PDFBiomechanical behavior of titanium, cobalt-chromium, zirconia, and PEEK frameworks in implant-supported prostheses: a dynamic finite element analysis.
BMC Oral Health
January 2025
Department of Prosthodontics, Faculty of Dentistry, Hacettepe University, 06230, Sıhhiye/Altındağ, Ankara, Turkey.
Background: The mechanical properties of framework materials significantly influence stress distribution and the long-term success of implant-supported prostheses. Although titanium, cobalt-chromium, zirconia, and polyether ether ketone (PEEK) are widely used, their biomechanical performance under dynamic loading conditions remains insufficiently investigated. This study aimed to evaluate the biomechanical behavior of four framework materials with different Young's modulus using dynamic finite element stress analysis.
View Article and Find Full Text PDFMolding Quality and Biological Evaluation of a Two-Stage Titanium Alloy Dental Implant Based on Combined 3D Printing and Subtracting Manufacturing.
ACS Omega
December 2024
State Key Laboratory of Oral & Maxillofacial Reconstruction and Regeneration & National Clinical Research Center for Oral Diseases & Shaanxi Engineering Research Center for Dental Materials and Advanced Manufacture, Department of Oral Implants, School of Stomatology, The Fourth Military Medical University, Xi'an 710032, Shaanxi, P. R. China.
Metal 3D printing has been used in the manufacturing of dental implants. Its technical advantages include high material utilization and the capacity to form arbitrarily complex structures. However, 3D printing alone is insufficient for manufacturing two-stage titanium implants due to the limited precision in printing titanium alloy parts.
View Article and Find Full Text PDFStructure and composition of early biofilms formed on dental implants are complex, diverse, subject-specific and dynamic.
NPJ Biofilms Microbiomes
December 2024
Department of Prosthetic Dentistry and Biomedical Materials Science, Hannover Medical School, Hannover, Germany.
Biofilm-associated peri-implant infections pose a major problem in modern medicine. The understanding of biofilm development is hampered by biofilm complexity and the lack of robust clinical models. This study comprehensively characterized the dynamics of early biofilm formation in the transmucosal passage of implant abutments in 12 patients.
View Article and Find Full Text PDFEffect of CAD/CAM Abutment Morphology on the Outcomes of Implant Therapy: A Randomized Controlled Trial.
Clin Oral Implants Res
December 2024
Department of Medicine, Infection, and Immunity, Harvard School of Dental Medicine, Boston, Massachusetts, USA.
Objectives: Variations in transmucosal abutment contour design may affect the outcomes of implant therapy. This randomized controlled trial was primarily aimed at testing the effect that CAD/CAM zirconia abutments with either a concave or linear divergent transmucosal morphology have on peri-implant mucosal dynamics and indicators of peri-implant health at 1 year after final implant-supported prosthesis insertion in the anterior maxilla.
Materials And Methods: Following computer-guided implant placement and osseointegration, eligible subjects were randomized into either the experimental (concave morphology) or the control (linear divergent morphology) group.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!