The pitting corrosion resistance and passive behavior of type 304 borated stainless steels (Fe⁻18Cr⁻12Ni⁻1.5Mn⁻(0.19, 0.78, and 1.76 wt %)B) manufactured through conventional ingot metallurgy were investigated. The alloys were composed of an austenitic matrix and Cr₂B phase, and the volume fraction of Cr₂B increased from 1.68 to 22.66 vol % as the B content increased from 0.19 to 1.76 wt %. Potentiodynamic polarization tests measured in aqueous NaCl solutions revealed that the pitting corrosion resistance was reduced as the B content increased and the pits were initiated at the matrix adjacent to the Cr₂B phase. It was found that the reduced resistance to pitting corrosion by B addition was due to the formation of more defective and thinner passive film and increased pit initiation sites in the matrix.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6267041 | PMC |
| http://dx.doi.org/10.3390/ma11112097 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Intelligent antibacterial coatings based on sensitive response and periodic fast drug release for long-term defense against corrosion induced by sulfate-reducing bacteria.
J Colloid Interface Sci
January 2025
Department of Materials Science and Engineering, Shaanxi Province Key Laboratory of Corrosion and Protection, Xi'an University of Technology, Xi'an 710048 PR China.
Pitting corrosion caused by sulfate-reducing bacteria (SRB) significantly shortens the lifespan of metallic pipelines. Antibacterial coatings containing S-responsive drug-loaded nanocontainers represent a promising method to mitigate SRB corrosion. However, the challenge of balancing rapid bactericide release with continuous antibacterial effect limits their practical application.
View Article and Find Full Text PDFIn Situ Raman Spectroscopy for Early Corrosion Detection in Coated AA2024-T3.
Sensors (Basel)
December 2024
TDA Research Inc., Golden, CO 80403, USA.
Here we describe the synthesis and evaluation of a molecular corrosion sensor that can be applied in situ in aerospace coatings, then used to detect corrosion after the coating has been applied. A pH-sensitive molecule, 4-mercaptopyridin (4-MP), is attached to a gold nanoparticle to allow surface-enhanced Raman-scattering (SERS) for signal amplification. These SERS nanoparticles, when combined with an appropriate micron-sized carrier system, are incorporated directly into an MIL-SPEC coating and used to monitor the process onset and progression of corrosion using pH changes occurring at the metal-coating interface.
View Article and Find Full Text PDFDynamic Electrochemical Impedance Spectroscopy in Galvanostatic Mode as a Tool for Passive Layer State Monitoring in a Chloride Solution Under a Mechanical Load.
Materials (Basel)
January 2025
Department of Corrosion and Electrochemistry, Faculty of Chemistry, Gdansk University of Technology, Narutowicza 11/12 Str., 80-233 Gdansk, Poland.
Mechanical stress is one of the factors influencing the initiation of pitting corrosion and deterioration of the protective properties of the passive layer on stainless steel. The tests carried out on AISI 304L stainless steel showed that, in the 3.5% NaCl environment for samples loaded in the elastic and plastic range, no pitting corrosion initiation was observed.
View Article and Find Full Text PDFErosion-Corrosion Behavior of 316L Stainless Steel in Chloropropene.
Materials (Basel)
December 2024
School of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410000, China.
The objective of this study is to investigate the impact of different pH values and chloropropene flow rates on the erosion-corrosion behavior of 316L stainless steel. The influence of various factors on the surface morphology was analyzed using scanning electron microscopy, X-ray powder diffractometry, and electrochemical impedance spectroscopy techniques. The results revealed that at a pH value of 3.
View Article and Find Full Text PDFEffect of Ce Content on Modification Behavior of Inclusions and Corrosion Resistance of 316L Stainless Steel.
Materials (Basel)
December 2024
School of Rare Earth Industry (School of Rare Earth Engineering and Technology), Inner Mongolia University of Science and Technology, Baotou 014010, China.
The changes in the inclusions in 316L stainless steel before and after Ce addition were studied by adding different contents of Ce. The effects of rare earth Ce treatment on the modification of MnS inclusions in steel and the pitting corrosion resistance of 316L stainless steel are studied by field-emission scanning electron microscopy, laser confocal microscopy, the 6% FeCl corrosion weight loss test, and Tafel polarization curve test. The results show that the addition of Ce reduces the corrosion rate of stainless steel in 6% FeCl solution, and reduces the number and size of corrosion pits.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!