Industrial gelatins have different physicochemical properties that mainly depend of the raw materials origin and the extraction conditions. These properties are closely related to the molar mass distribution of these gelatins. Several methods exist to characterize molar mass distribution of polymer, including the Asymmetrical Flow Field Flow Fractionation method. The goal of this study is to analyze the relationship between physicochemical properties and the gelatins molar mass distribution obtained by Asymmetrical Flow Field Flow Fractionation. In this study, 49 gelatins samples extracted from pig skin are characterized in terms of gel strength and viscosity and their molar mass distribution are analyzed by Asymmetrical Flow Field Flow Fractionation coupled to an Ultraviolet and Multi Angle Light Scattering detector. This analytical method is an interesting tool for studying, simultaneously, the primary chains and the high-molar-mass fraction corresponding to the polymer chains. Correlation analysis between molar mass distribution data from the different fractions highlights the importance of high molar mass polymer chains to explain the gel strength and viscosity of gelatins. These results are confirmed by an additional chemometric approach based on the UV absorbance of gelatin fractograms to predict gel strength (r2Cal = 0.85) and viscosity (r2Cal = 0.79).
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6177121 | PMC |
| http://journals.plos.org/plosone/article?id=10.1371/journal.pone.0203595 | PLOS |
Publication Analysis
Top Keywords
Similar Publications
Acid-Enhanced Photoiniferter Polymerization under Visible Light.
Angew Chem Int Ed Engl
December 2024
ETH Zurich, Materials, Vladimir-Prelog-Weg 1-5/10, 8093, Zürich, SWITZERLAND.
Photoiniferter (PI) is a promising polymerization methodology, often used to overcome restrictions posed by thermal reversible addition-fragmentation chain-transfer (RAFT) polymerization. However, in the overwhelming majority of reports, high energy UV irradiation is required to effectively trigger photolysis of RAFT agents and facilitate the polymerization, significantly limiting its potential, scope, and applicability. Although visible light PI has emerged as a highly attractive alternative, most current approaches are limited to the synthesis of lower molecular weight polymers, and typically suffer from prolonged reaction times, extended induction periods, and higher dispersities.
View Article and Find Full Text PDFPurification and structural characterization of a neutral polysaccharide from Boletus auripes using self-made quaternary chitosan cryogel.
Int J Biol Macromol
December 2024
College of Chemistry and Molecular Sciences, Hubei Engineering Center of Natural Polymer-Based Medical Materials, Wuhan University, Wuhan 430072, China. Electronic address:
The purification of polysaccharides is an essential preliminary step in determining their chemical structure, although it presents significant challenges. In this research, a macro-porous monolith of quaternary chitosan cryogel was synthesized for the purification of a neutral polysaccharide from Boletus auripes. A homogeneous neutral polysaccharide (BAP-1a1) with a weight-average molecular weight of 4.
View Article and Find Full Text PDFFabrication, structural, physical, optical characteristics and γ-ray attenuation capacity of borosilicate glasses doped with GdO.
Sci Rep
December 2024
Department of Physics, Faculty of Science, Menoufia University, Shebin El-Koom, Menoufia, 32511, Egypt.
Barium fluoride borosilicate glass samples reinforced with varying amounts of GdO (BSBLG0-BSBLG4) have been manufactured using the conventional melt quenching procedure in order to provide additional research on the type of borosilicate glass. Structural, physical, and linear optical characteristics as well as γ-ray attenuation capacity of barium fluoride borosilicate doped with GdO was investigated. X-ray diffraction pattern proving the amorphous nature of the glass samples due to the absence of a distinctive crystalline characteristic peak.
View Article and Find Full Text PDFFluoroform (CHF) Production from CFCHO Photolysis and Implications for the Decomposition of Hydrofluoroolefins and Hydrochlorofluoroolefins in the Atmosphere.
J Am Chem Soc
December 2024
School of Chemistry, University of New South Wales, Kensington, NSW 2052, Australia.
Hydrofluoroolefins (HFOs) and hydrochlorofluoroolefins (HCFOs) are the leading synthetic replacements for compounds successively banned by the Montreal Protocol and amendments. HFOs and HCFOs readily decompose in the atmosphere to form fluorinated carbonyls, including CFCHO in yields of up to 100%, which are then photolyzed. A long-standing issue, critical for the transition to safe industrial gases, is whether atmospheric decomposition of CFCHO yields any quantity of CHF (HFC-23), which is one of the most environmentally hazardous greenhouse gases.
View Article and Find Full Text PDFSynergistic Pathways in PLA Breakdown and PTMC Formation: A One-Pot Eutectic-Driven Recycling Mechanism.
Angew Chem Int Ed Engl
December 2024
Université de Mons: Universite de Mons, Sciences, BELGIUM.
This study introduces a novel one-pot strategy for the chemical valorization of poly(lactic acid) (PLA), coupling its base-catalyzed depolymerization with the ring-opening polymerization (ROP) of trimethylene carbonate (TMC). The process exploits an eutectic mixture of lactide (LA) and TMC, which lowers the thermal input required for PLA degradation. Using potassium aryloxide (KOArtBu) as a bifunctional catalyst, the PLA is first quickly hydrolyzed into oligomers or lactic acid, which subsequently initiate the slower polymerization of TMC.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!