The automated aseptic preparation of ready-to-administer antineoplastic drug solutions with robotic systems reduces the risk of occupational exposure. However, the surfaces in the preparation area of the robot are to be cleaned by wiping with an appropriate cleaning solution. The aim of the study was to evaluate the cleaning efficacy of four cleaning solutions on four surface materials installed in the APOTECAchemo robot. Predefined amounts of cisplatin (Cis), 5-fluorouracil (5-FU), and cyclophosphamide (CP) were intentionally spread on test plates made of stainless steel, aluminium, polyoxymethylene, and polycarbonate just as installed in the robotic system APOTECAchemo. After drying, the plates were cleaned with 0.2% ethanolic NaOH, 0.23% isopropanolic sodium dodecylsulfate (SDS-2P), 0.5% sodium hypochlorite (NaOCl), and 0.1% benzalkonium chloride (BZK) solutions following a standardized wiping protocol. Residual contamination was recovered with wipe tests, Pt was quantified by voltammetry, and 5-FU and CP was quantified by gas chromatography-tandem mass spectrometry (GC-MSMS). The mean residual contamination after cleaning and the cleaning efficacy (CE) rates were calculated and aggregated on different levels. The CE rates varied between 81.5% and 100% and lay in the majority of cases above 90%. The lowest CE rates were registered for Pt contamination. Especially on aluminium surfaces the residual contamination was high. The overall CE rates of the three different drugs and four different surface types amounted to 98.3% for NaOCl, 97.9% for SDS-2P, 96.9% for ethanolic NaOH, and 96.5% for BZK. The tested cleaning solutions proved to be higher than 90% in most cases, but none of them was able to eliminate 100% of the intentional surface contamination of three antineoplastic drugs on the test plates. The cleaning efficacy varied according to the different surface types and antineoplastic drug. Results could be used in the daily clinical practice to develop and implement effective cleaning procedures.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1080/15459624.2018.1526384 | DOI Listing |
Int J Biol Macromol
January 2025
Tianjin Key Laboratory of Pulp & Paper, Tianjin University of Science and Technology, Tianjin, 300457, PR China; State Key Laboratory of Biobased Fiber Manufacturing Technology, Tianjin University of Science and Technology, Tianjin 300457, PR China. Electronic address:
Poly (lactic acid) (PLA) is a widely produced bio-based polymer known for its biodegradability and renewability, but its brittleness, low heat resistance, and weak mechanical properties limit its broader use. To address these challenges, TEMPO-oxidized cellulose nanofibers (TOCNF) were extracted from dissolving pulp using TEMPO oxidation and high-pressure homogenization. These TOCNF were modified with silane to reduce hydrophilicity and improve compatibility with PLA.
View Article and Find Full Text PDFSci Total Environ
January 2025
State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming, Yunnan 650093, PR China; Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan 650093, PR China. Electronic address:
Solid waste is one of the primary contributors to environmental pollution currently, it is crucial to enhance the prevention and control of solid waste pollution in environmental management. The effectiveness of the second stage of purification in the industrial zinc hydrometallurgy is determined by the concentration of cobalt ion. Manual testing and monitoring of cobalt ion concentration are time consuming and costly, and prone to delays, which can result in discharge of cobalt ion concentration that does not meet the standards, leading to water pollution.
View Article and Find Full Text PDFWater Environ Res
January 2025
Zhejiang Key Laboratory of Petrochemical Environmental Pollution Control, Zhejiang Ocean University, Zhoushan, P. R. China.
The discharge of oil-laden wastewater from industrial processes and the frequent occurrence of oil spills pose severe threats to the ecological environment and human health. Membrane materials with special wettability have garnered attention for their ability to achieve efficient oil-water separation by leveraging the differences in wettability at the oil-water interface. These materials are characterized by their simplicity, energy efficiency, environmental friendliness, and reusability.
View Article and Find Full Text PDFSci Rep
January 2025
Computational Fluid Dynamics Laboratory, School of Mechanical Engineering, VIT, Vellore, 632014, India.
Stenosis causes the narrowing of arteries due to plaque buildup, which impedes blood flow and affects flow dynamics. This work numerically analyzes flow fluctuations in stenosed arteries under realistic physiological conditions (resting and exercise) and external body acceleration. The artery is inclined at angle , and blood rheology is modeled using a generalized power-law fluid.
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, China.
Inspired by the adhesion differences on the surfaces of fresh and dried rose petals, a rose bionic self-cleaning fog collector (RBSC) was designed and prepared to realize a self-driven fog harvesting function. The droplet detachment iteration rate was revealed by the regulating mechanism of the surface adhesion force of the RBSC and the influence of bionic texture parameters, as demonstrated through the fog harvesting experiment and droplet detachment failure analysis. Through the surface adhesion force regulation, the probability of droplet dissipation with the airflow is reduced by increasing the falling droplets' mass, and the single surface fog capture efficiency is up to 740 mg cm h.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!