Synthesis and Morphology Evolution of Ultrahigh Content Nitrogen-Doped, Micropore-Dominated Carbon Materials as High-Performance Supercapacitors.

ChemSusChem

State Key Laboratory of Power Metallurgy, Department of Polymer Materials and Engineering, Central South University, Changsha, Hunan, 410083, P. R. China.

Published: November 2018

Nitrogen-doped carbon-based materials including nanocarbons, graphene, and conductive polymers are impressive as supercapacitor electrodes. However, ultrahigh nitrogen contents, micropore dominated, and morphology evolving carbonaceous electrodes have not achieved until now which are crucial for supercapacitor. Herein, we prepare a novel fumaronitrile (FUM) derived covalent triazine framework (FUM-CTF) and activated it by using KOH at different temperatures to obtain the corresponding carbon materials, which were used as supercapacitor electrode materials. Specially, the FUM-700 (sample activated at 700 °C) possesses an excellent specific capacitance of 400 F g at a current density of 1 A g and considerable energy density over 18 Wh kg in KOH (6 m) aqueous electrolyte. In addition, this electrode shows 260 F g at a current density of 20 A g for charge/discharge operation. Furthermore, the FUM-700 electrode demonstrates extraordinary electrochemical stability with 97 % retention after 10 000 cycles at 10 A g . Ultrahigh nitrogen contents, the microporous structure, and the inner nanoparticle morphology work in concert to contribute to the superior electrochemical performance of FUM-700. Our work might give some hints to help design other high-performance nitrogen-containing supercapacitor electrode materials.

Download full-text PDF

Source
http://dx.doi.org/10.1002/cssc.201801892DOI Listing

Publication Analysis

Top Keywords

carbon materials
8
ultrahigh nitrogen
8
nitrogen contents
8
supercapacitor electrode
8
electrode materials
8
current density
8
materials
5
synthesis morphology
4
morphology evolution
4
evolution ultrahigh
4

Similar Publications

Enhancing Carbon Monoxide Tolerance in Low-Temperature PEM Fuel Cells through Carbon Nitride Surface Modification.

ACS Appl Mater Interfaces

January 2025

State Key Laboratory of Physical Chemistry of Solid Surfaces, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, China.

Low-temperature proton exchange membrane fuel cells (PEMFCs) reuqire highly pure hydrogen gas due to their extreme sensitivity to carbon monoxide (CO) contamination, which poses a challenge for using cost-effective reformed hydrogen sources. To address this issue, we have developed a surface modification strategy by applying a 0.5-0.

View Article and Find Full Text PDF

Per- and polyfluoroalkyl substances (PFAS) are extremely stable chemicals that are essential for modern life and decarbonization technologies. Yet PFAS are persistent pollutants that are harmful to human health. Hexafluoropropylene oxide dimer acid (GenX), a replacement for the PFAS chemical perfluorooctanoic acid, continues to pollute waterways.

View Article and Find Full Text PDF

High-Rate 4.2 V Solid-State Potassium Batteries by In Situ Polymerized Epoxide Ether Electrolyte.

Nano Lett

January 2025

College of Materials Science and Engineering, Hunan Joint International Laboratory of Advanced Materials and Technology of Clean Energy, Hunan Province Key Laboratory for Advanced Carbon Materials and Applied Technology, Hunan University, Changsha 410082, China.

Solid-state metallic potassium batteries (SSMPBs) afresh have attracted incremental attention because of their potential to supplement solid-state metallic lithium batteries. However, SSMPBs suffer poor electrochemical performances due to the low ionic conductivity of solid electrolytes and huge electrode/electrolyte interfacial resistance. Herein, high-rate SSMPBs are achieved by in situ ring-opening polymerization of 1,3-dioxolane with succinonitrile as a plasticizer and Al(OTf) as the catalyst, where the succinonitrile enables short-chain polyether electrolytes.

View Article and Find Full Text PDF

Large-area radiation-modulated thermoelectric fabrics for high-performance thermal management and electricity generation.

Sci Adv

January 2025

National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou, Jiangsu 215123, China.

Flexible thermoelectric systems capable of converting human body heat or solar heat into sustainable electricity are crucial for the development of self-powered wearable electronics. However, challenges persist in maintaining a stable temperature gradient and enabling scalable fabrication for their commercialization. Herein, we present a facile approach involving the screen printing of large-scale carbon nanotube (CNT)-based thermoelectric arrays on conventional textile.

View Article and Find Full Text PDF

Enhancing transport and chemomechanical properties in cathode composites is crucial for the performance of solid-state batteries. Our study introduces the filler-aligned structured thick (FAST) electrode, which notably improves mechanical strength and ionic/electronic conductivity in solid composite cathodes. The FAST electrode incorporates vertically aligned nanoconducting carbon nanotubes within an ion-conducting polymer electrolyte, creating a low-tortuosity electron/ion transport path while strengthening the electrode's structure.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!