Low-dimensional halide perovskites have recently attracted intense interest as alternatives to the three-dimensional (3D) perovskites because of their greater tunability and higher environmental stability. Herein, we present the new homologous 2D series (NHC HNH)(CHNH) Pb I ( m = 4-9; n = 1-4), where m represents the carbon-chain number and n equals layer-thickness number. Multilayer ( n > 1) 2D perovskites incorporating diammonium cations were successfully synthesized by the solid-state grinding method for m = 4 and 6 and by the solution method for m = 7-9. Structural characterization by single-crystal X-ray diffraction for the m = 8 and m = 9 series ( n = 1-4) reveals that these compounds adopt the Cc space group for even n members and Pc for odd n members. The optical bandgaps are 2.15 eV for two-layer ( n = 2), 2.01 eV for three-layer ( n = 3), and 1.90 eV for four-layer ( n = 4). The materials exhibit excellent solution processability, and casting thin-films of the n = 3 members was successfully accomplished. The films show a clear tendency for the higher- m members to have preferred orientation on the glass substrate, with m = 8 exhibiting almost perfect vertical layer orientation and m = 9 displaying both vertical and parallel layer orientation, as confirmed by grazing-incidence wide-angle X-ray scattering (GIWAXS) measurements. The vertical layer orientation for the (NHCHNH)(CHNH)PbI member results in the best thermal, light, and air stability within this series, thus showing excellent potential for solar cell applications.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/jacs.8b07712 | DOI Listing |
Polymers (Basel)
January 2025
Department of Mechanical Engineering, Sogang University, Seoul 04107, Republic of Korea.
Metallic injection molding combines aluminum flake metallic pigments with polymers to directly produce components with metallic luster, improving production efficiency and reducing environmental impact. However, flake line defects that occur in regions where ribs or flow paths intersect remain a significant challenge. This study proposes a velocity model that considers the flow characteristics between the surface and core layers and an alignment model that incorporates the orientation of aluminum flakes to predict appearance defects.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
Institute of Chemistry and Chemical Technology, Faculty of Natural Sciences and Technology, Riga Technical University, P. Valdena 3, LV-1048 Riga, Latvia.
Despite the impressive properties of additively manufactured products, their inherent anisotropy is a crucial challenge for polymeric parts made via fused filament fabrication (FFF). This study compared the tensile, thermophysical, smoke density, and toxicity characteristics of Ultem 9085 (a blend of polyetherimide and polycarbonate) for samples printed in various orientations (X, Y, and Z). The results revealed that mechanical properties, such as elastic modulus and tensile strength, significantly differed from the Z printing orientation, particularly in the X and Y printing layer orientations.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Mechnical and Vehicle Engineering, Hunan University, Changsha 411082, China.
Chip defect detection is a crucial aspect of the semiconductor production industry, given its significant impact on chip performance. This paper proposes a lightweight neural network with dual decoding paths for LED chip segmentation, named LDDP-Net. Within the LDDP-Net framework, the receptive field of the MobileNetv3 backbone is modified to mitigate information loss.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Institute of Nanotechnologies, Electronics and Equipment Engineering, Southern Federal University, 347922 Taganrog, Russia.
One of the challenging problems in the research and development of vibration sensors relates to the formation of Ohmic contacts for the removal of an electrical signal. In some cases, it is proposed to use arrays of carbon nanotubes (CNTs), which can serve as highly elastic electrode materials for vibration sensors. The purpose of this work is to study the effect of a current-collecting layer of CNTs grown over silicon on the properties of a lead zirconate titanate (PZT) film, which is frequently employed in mechanical vibration sensors or energy harvesters.
View Article and Find Full Text PDFMaterials (Basel)
January 2025
Management Faculty, AGH University, Gramatyka 10 Str., 30-067 Kraków, Poland.
Additive manufacturing is a technology that creates objects by adding successive layers of material. The 3D method is an alternative to subtractive production, in which production involves removing material from the initial solid. 3D printing requires the initial design of the manufactured object using computer design, for example, one of the following programs: CAD, 3DCrafter, Wings 3D, Cinema 3, Blender, 3ds Max, Autodesk Inventor, and others.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!