The combinational effects of a bioengineered scaffold loaded with neurotrophins and rehabilitation training on spasticity observed after spinal cord injury (SCI) has not been studied. We used an animal model of moderate contusion injury at T9/T10 that received bioengineered scaffold poly N-isopropylacrylamide-g-poly ethylene glycol (PNIPAAm-g-PEG) loaded with BDNF/NT3 followed by body weight supported treadmill training (BWSTT) and assessed the efficacy of the combinational bioengineered approaches in treating spasticity. Five animal groups were included: Group 1: Sham, Group 2: Injury (SCI), Group 3: SCI + BWSTT (BWSTT), Group 4: SCI + PNIPAAm-g-PEG loaded with BDNF/NT3 (Transplant), and Group 5: SCI + PNIPAAm-g-PEG loaded with BDNF/NT3 + BWSTT (Combinational). Results indicate no significant changes in the BBB scores of animals among various groups, however, a significant restoration in the rate depression property of H-reflex was observed in both BWSTT and Combinational animals. Transplant group reported no improvement in the rate depression property of H-reflex and were similar to SCI only group. Histological findings report restoration of the chloride cotransporter (KCC2) labeling in both BWSTT and Combinational animals and down-regulation of KCC2 in both SCI and Transplant only animals. Findings from this study confirm that rehabilitation training is critical in restoring H-reflex responses and transplantation therapies alone cannot restore these responses after SCI. Also, although no significant difference was observed between the BWSTT and Combinational animals, comparable improvements in the two groups does open new pathways to exploring unique tissue-engineering approaches with promising clinical application for individuals with SCI.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s00221-018-5344-x | DOI Listing |
PLoS One
January 2025
Department of Orthopaedic Surgery, The Second Affiliated Hospital of Zunyi Medical University, Zunyi, Honghuagang District, Guizhou, China.
With the rise of bone tissue engineering (BET), 3D-printed HA/PCL scaffolds for bone defect repair have been extensively studied. However, little research has been conducted on the differences in osteogenic induction and regulation of macrophage (MPs) polarisation properties of HA/PCL scaffolds with different fibre orientations. Here, we applied 3D printing technology to prepare three sets of HA/PCL scaffolds with different fibre orientations (0-90, 0-90-135, and 0-90-45) to study the differences in physicochemical properties and to investigate the response effects of MPs and bone marrow mesenchymal stem cells (BMSCs) on scaffolds with different fibre orientations.
View Article and Find Full Text PDFTissue Eng Part A
January 2025
C. Wayne McIlwraith Translational Medicine Institute, Colorado State University, Fort Collins, Colorado, USA.
Scaffolds made from cartilage extracellular matrix are promising materials for articular cartilage repair, attributed to their intrinsic bioactivity that may promote chondrogenesis. While several cartilage matrix-based scaffolds have supported chondrogenesis and/or , it remains a challenge to balance the biological response (e.g.
View Article and Find Full Text PDFJ Mater Sci Mater Med
January 2025
Tissue Engineering & Additive Manufacturing (TEAM) Lab, Centre for Nanotechnology & Advanced Biomaterials (CeNTAB), ABCDE Innovation Centre, School of Chemical & Biotechnology (SCBT), SASTRA Deemed University, Thanjavur, 613401, India.
Preservation and long-term storage of readily available cell-laden tissue-engineered products are major challenges in expanding their applications in healthcare. In recent years, there has been increasing interest in the development of off-the-shelf tissue-engineered products using the cryobioprinting approach. Here, bioinks are incorporated with cryoprotective agents (CPAs) to allow the fabrication of cryopreservable tissue constructs.
View Article and Find Full Text PDFBiomater Sci
January 2025
Institute of Chemistry, University of Campinas, UNICAMP, Campinas 13083-970, São Paulo, Brazil.
The pivotal roles played by nitric oxide (NO) in tissue repair, inflammation, and immune response have spurred the development of a wide range of NO-releasing biomaterials. More recently, 3D printing techniques have significantly broadened the potential applications of polymeric biomaterials in biomedicine. In this context, the development of NO-releasing biomaterials that can be fabricated through 3D printing techniques has emerged as a promising strategy for harnessing the benefits of localized NO release from implantable devices, tissue regeneration scaffolds, or bandages for topical applications.
View Article and Find Full Text PDFRegen Biomater
November 2024
Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Prince of Songkla University, Hatyai 90110, Thailand.
Alveolar ridge loss presents difficulties for implant placement and stability. To address this, alveolar ridge preservation (ARP) is required to maintain bone and avoid the need for ridge augmentation using socket grafting. In this study, a scaffold for ARP was created by fabricating a 3D porous dense microfiber silk fibroin (mSF) embedded in poly(vinyl alcohol) (PVA), which mimics the osteoid template.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!