Purpose: To compare the fracture toughness of four different CAD/CAM materials, (VM) Vitablocs Mark II, (IP) IPS e.max CAD, (LU) LAVA Ultimate, and (VE) Vita Enamic under long thermocycling conditions.
Methods: Each type of ceramic block was sectioned into beams (n=9) with dimensions of 14×3×2.5 mm (L × W × H). All four ceramics were submitted to different conditions: the desiccator or distilled water, each for 7 days. The third and fourth conditions involved the specimens being submitted to 60,000 and 120,000 thermocycles in water respectively. The dwelling time was 52 seconds at 5° and 55°C. A three-point bend test with a universal loading machine on notched samples was per-formed. Furthermore, a fractographic analyses was made by scanning electron microscopy (SEM) to determine if any of these conditions influenced the type of fracture. Data were analyzed by two-way ANOVA (α= 0.05).
Results: A significant difference in fracture toughness (P< 0.05) was found among the groups; IP (4.20±1.23) had the highest value followed by VE (2.02±0.39), which did not have a statistically significant difference from LU (1.96±0.42). The lower value and statistical difference for VM was 1.52±0.35. The ceramics performed better after they were hydrated, while the polymer-based materials had the fracture toughness means decreased after the thermocycles.
Clinical Significance: A significant difference in fracture toughness (P<0.05) was found among the groups; IP had the highest value followed by VE, which was not statistically significantly different from LU. The ceramics performed better after they were hydrated, while the polymer-based materials had fracture toughness means decreased after thermocycling.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
A Review on Multi-Scale Toughening and Regulating Methods for Modern Concrete: From Toughening Theory to Practical Engineering Application.
Research (Wash D C)
December 2024
School of Materials Science and Engineering, Jiangsu Key Laboratory of Construction Materials, Southeast University, Nanjing, China.
Concrete is the most widely used and highest-volume basic material in the word today. Enhancing its toughness, including tensile strength and deformation resistance, can boost the structural load-bearing capacity, minimize cracking, and decrease the amount of concrete and steel required in engineering projects. These advancements are crucial for the safety, durability, energy efficiency, and emission reduction of structural engineering.
View Article and Find Full Text PDFThe Structure-Mechanics Relationship of Bamboo-Epidermis and Inspired Composite Design by Artificial Intelligence.
Adv Mater
December 2024
Laboratory for Multiscale Material Modelling, Syracuse University, 151L Link Hall, Syracuse, NY, 13244, USA.
Bamboo culm has been widely used in engineering for its high strength, lightweight, and low cost. Its outermost epidermis is a smooth and dense layer that contains cellulose, silica particles, and stomata and acts as a water and mechanical barrier. Recent experimental studies have shown that the layer has a higher mechanical strength than other inside regions.
View Article and Find Full Text PDFObservation and Control of Single-Component Adhesion Interphase of Polyamide 66 through Confocal Raman Microspectroscopy.
ACS Appl Mater Interfaces
December 2024
Department of Chemical Science and Engineering, Graduate School of Engineering, Kobe University, Rokko, Nada Kobe 657-8501, Japan.
Manufacturing using adhesion technology has attracted much attention. Examples of adhesion include the lay-up of carbon fiber reinforced thermoplastic prepregs and the lamination of food packaging. In single-component adhesion systems, the analysis of the boundary region poses challenges because of the absence of chemical and physical discrimination at the adhesion interphase.
View Article and Find Full Text PDFSuper Tough Multifunctional MXene/PAA-CS Double Network Hydrogels with High Mechanical Sensing Properties and Excellent EMI Shielding Performance.
Small
December 2024
School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, 230026, China.
Hydrogels present significant potential in flexible materials designed for electromagnetic interference (EMI) shielding, attributed to their soft, stretchable mechanical properties and water-rich porous structures. Unfortunately, EMI shielding hydrogels commonly suffer from low mechanical properties, deficient fracture energy, and low strength, which limit the serviceability of these materials in complex mechanical environments. In this study, the double network strategy is successfully utilized along with the Hofmeister effect to create MXene/PAA (polyacrylic acid)-CS (chitosan) hydrogels and further strengthen and toughen the gel with (NH)SO solution.
View Article and Find Full Text PDFLimb Salvage Versus Amputation: A Review of Variables Influencing the Assessment and Decision-Making in Complex Limb Fracture Management.
Cureus
November 2024
Emergency Medicine, West Midlands Deanery, Birmingham, GBR.
Complex limb injuries are combination injuries that involve all components of a limb's tissue, such as skin, bone with its surrounding soft tissue cover, and neurovascular elements. Complex limb trauma often has a background of a significant mechanism of injuries such as high-velocity road traffic accidents, ballistic injuries, industrial accidents, and other major mechanisms of injuries which involve high amounts of energy transfer through these tissue layers. These injuries pose a major challenge to trauma and orthopaedic surgeons.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!