2,2-Dibromo-3-nitrilopropionamide (DBNPA) is a major biocide in hydraulic fracturing fluids. Most biocides in fracturing fluids are considered to have low acute toxicity to mammals, but little information is available in the literature regarding the toxic actions of DBNPA on mammalian cells. This information is important to suggest the DBNPA toxicity on wild mammals. In this study, the effects of DBNPA on rat thymocytes were studied using flow cytometric techniques in order to further characterize the cytotoxicity of DBNPA for its safe use. DBNPA at 3-7.5 μM produced a steep concentration-dependent increase in cell lethality. At 5 μM, DBNPA significantly depolarized the membranes with a disturbance of the asymmetrical distribution of membrane phospholipids. The lethal effect of DBNPA was completely abolished under cold conditions, and was augmented in the presence of ethanol. It is suggested that the lethal action of DBNPA is linked to changes in membrane fluidity. Because the concentration-dependent change of DBNPA-induced lethal action was very steep under conditions, the adverse actions of DBNPA on wild mammals are concerning, even though such reports have not yet surfaced.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6062308 | PMC |
http://dx.doi.org/10.1039/c6tx00027d | DOI Listing |
Cureus
December 2024
Anesthesiology, Showa University Northern Yokohama Hospital, Yokohama, JPN.
Flail chest is a life-threatening condition characterized by multiple rib fractures that result in a partially free rib cage. Thoracic paravertebral block (TPVB) allows visualization of the needle tip under ultrasound guidance and can be safely performed, unlike epidural anesthesia where the needle tip cannot be visualized. Here, we describe a case of flail chest in whom TPVB was used, as it provides the same level of analgesia as epidural anesthesia and has a perfect analgesic effect.
View Article and Find Full Text PDFLangmuir
January 2025
State Key Laboratory of Water Resources Engineering and Management, Wuhan University, Wuhan 430072, China.
Mineral precipitation is ubiquitous in natural and engineered environments, such as carbon mineralization, contaminant remediation, and oil recovery in unconventional reservoirs. The precipitation process continuously alters the medium permeability, thereby influencing fluid transport and subsequent reaction kinetics. The diversity of preferential precipitation zones controls flow and transport efficiency as well as the capacity of mineral sequestration and immobilization.
View Article and Find Full Text PDFMolecules
December 2024
National Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum, Beijing 102249, China.
Hydraulic fracturing of deep, high-temperature reservoirs poses challenges due to elevated temperatures and high fracture pressures. Conventional polymer fracturing fluid (QCL) has high viscosity upon adding cross-linking agents and significantly increases wellbore friction. This paper examines a polymer fracturing fluid with pH response and low friction.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Department of Power Systems and Environmental Protection Facilities, Faculty of Mechanical Engineering and Robotics, AGH University of Krakow, 30-059 Krakow, Poland.
This study explores the impact of structural modifications on the stress distribution and flow characteristics of a nozzle box in a steam turbine, specifically targeting the components made from high-strength StE460 steel. Using Computational Fluid Dynamics (CFDs) and Thermal-Fluid-Structure Interaction (Thermal-FSI) simulations, we examine the effects of shortening the nozzle guide vanes by 7 mm. This novel approach significantly reduces the stress levels within the nozzle box segments, bringing them below the critical thresholds and thus enhancing component durability.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Jiangxi Provincial Key Laboratory of Materials Surface Engineering, School of Materials Science and Engineering, Jiujiang University, Jiujiang 332005, China.
To explore the feasibility of preparing Zn alloy bulk, Zn-6Cu deposit was prepared by cold-spraying additive manufacturing. Microstructure, tensile and wear behavior were investigated before and after heat treatment. Cold-sprayed Zn-6Cu deposit was constituted by irregular flattening particles and pores after heat treatment.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!