Introduction: Ilizarov bone transport for large bone defect is challenging and may end in distraction osteogenesis failure.
Material And Methods: Ten forearm and seven tibial defect cases with failed regeneration due to ischaemia during bone transport were studied retrospectively. Mean forearm and tibial defects were 5.5 ± 0.8 and 7.6 ± 1 cm respectively, or 22.3 ± 3.6 and 20 ± 2.3% as compared with healthy segments. Most patients had numerous previous operations (2.6 ± 0.5 and 3.4 ± 0.8 per patient, respectively), extensive scars locally and post-traumatic neuropathy. There were seven infected defects. Mechanical solutions used were (1) additional osteotomy and transport of the fragment to compact the ischaemic regenerate (10 forearms, 4 tibias) and (2) compaction of the connective tissue layer in the tibial regenerate with either two 5-mm steps (two cases) or gradually (one case).
Results: Bone integrity was restored in all the cases. Complete compensation of the defects was achieved in 12 patients with the first technique. Two patients with 8-cm ulna defects remained with residual discrepancy. In the forearm, mean compaction was 1.7 ± 0.4 cm. It took 25.7 ± 5.4 days followed by an average fixation period of 107.1 ± 11.8 days. In the tibia, mean longitudinal compaction by distraction measured 1.7 ± 0.8 cm. The second technique ended up with an acceptable shortening of 1 cm in two cases. Four centimeters were compressed in the third case gradually.
Conclusion: The technical solutions used for mechanical effects on the ischaemic distraction regenerate resulted in its rescue and bone union in all the cases.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s00264-018-4032-6 | DOI Listing |
Adv Mater
January 2025
Institute for Advanced Materials & Guangdong Provincial Key Laboratory of Optical Information Materials and Technology, South China Academy of Advanced Optoelectronics, South China Normal University, Guangzhou, 510006, China.
Laboratory-scale spin-coating techniques are widely employed for fabricating small-size, high-efficiency perovskite solar cells. However, achieving large-area, high-uniformity perovskite films and thus high-efficiency solar cell devices remain challenging due to the complex fluid dynamics and drying behaviors of perovskite precursor solutions during large-area fabrication processes. In this work, a high-quality, pinhole-free, large-area FAPbI perovskite film is successfully obtained via scalable blade-coating technology, assisted by a novel bidirectional Marangoni convection strategy.
View Article and Find Full Text PDFSci Rep
January 2025
Faculty of Mechanical Engineering, VŠB -Technical University of Ostrava, 17. listopadu 2172/15, 708 00, Ostrava-Poruba, Czech Republic.
Three types of commercial austenitic stainless steels, 1.4307 (AISI 304 L), 1.4404 (AISI 316 L) 1.
View Article and Find Full Text PDFSci Rep
January 2025
Department of Mechanical Engineering, Faculty of Engineering, Urmia University, Urmia, Iran.
This study investigates the nonlinear dynamics of a system with frequency-dependent stiffness using a MEMS-based capacitive inertial sensor as a case study. The sensor is positioned directly on a rotating component of a machine and consists of a microbeam clamped at both ends by fixed supports with a fixed central proof mass. The nonlinear behavior is determined by electrostatic forces, axial and bending motion coupling, and frequency-dependent stiffness.
View Article and Find Full Text PDFSci Rep
January 2025
School of Mechanical and Electrical Engineering, Quzhou College of Technology, Quzhou, 324000, China.
Pneumatic impactor is widely used in the drilling process of various medium and high hard rocks with poor drill ability. Currently, there is relatively little analysis on the impact of the inclination of the rock surface during the drilling process on the drilling efficiency and excavation capability of pneumatic impactors. Based on the dynamic theory of impact drilling and finite element method (FEM), the constitutive model of HJC criterion and INVENTOR 3D mechanical structure design software, a 3D numerical analysis system of piston-bit head-rock during pneumatic impactor drilling is established by ANSYS LS-DYNA, a nonlinear dynamic analysis software.
View Article and Find Full Text PDFMicrosyst Nanoeng
January 2025
Key Laboratory of Instrumentation Science and Dynamic Measurement Ministry of Education, North University of China, 030051, Taiyuan, China.
The alarming prevalence and mortality rates associated with cardiovascular diseases have emphasized the urgency for innovative detection solutions. Traditional methods, often costly, bulky, and prone to subjectivity, fall short of meeting the need for daily monitoring. Digital and portable wearable monitoring devices have emerged as a promising research frontier.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!