Magnesium alloys are widely used in aerospace vehicles and modern cars, due to their rapid machinability at high cutting speeds. A novel Edgeworth⁻Pareto optimization of an artificial neural network (ANN) is presented in this paper for surface roughness () prediction of one component in computer numerical control (CNC) turning over minimal machining time () and at prime machining costs (). An ANN is built in the Matlab programming environment, based on a 4-12-3 multi-layer perceptron (MLP), to predict , , and , in relation to cutting speed, , depth of cut, , and feed per revolution, . For the first time, a profile of an AZ61 alloy workpiece after finish turning is constructed using an ANN for the range of experimental values , , and . The global minimum length of a three-dimensional estimation vector was defined with the following coordinates: = 0.087 μm, = 0.358 min/cm³, = $8.2973. Likewise, the corresponding finish-turning parameters were also estimated: cutting speed = 250 m/min, cutting depth = 1.0 mm, and feed per revolution = 0.08 mm/rev. The ANN model achieved a reliable prediction accuracy of ±1.35% for surface roughness.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC5978185 | PMC |
| http://dx.doi.org/10.3390/ma11050808 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Review of advanced sensor system applications in grinding operations.
J Adv Res
January 2025
Department of Mechanics and Strength of Materials, Politehnica University Timisoara, 1 Mihai Viteazu Avenue, 300 222 Timisoara, Romania. Electronic address:
Background: Today, in a wide variety of industries, grinding operations are an extremely important finishing process for obtaining precise dimensions and meeting strict requirements for roughness and shape accuracy. However, the constant wear of abrasive tools during grinding negatively affects the dimensional and surface conditions of the workpiece. Therefore, effective monitoring of the wear process during grinding operations helps to predict tool life, plan maintenance and ensure consistent product quality.
View Article and Find Full Text PDFBifunctional modified bacterial cellulose-based hydrogel through sequence-dependent crosslinking towards enhanced antibacterial and cutaneous wound healing.
Int J Biol Macromol
January 2025
Department of Microbiology, College of Life Science, Key Laboratory for Agriculture Microbiology, Shandong Agricultural University, Tai'an 271018, PR China; School of Pharmacy, the Key Laboratory of Medical Antibacterial Materials of Shandong Province, Binzhou Medical University, Yantai 264003, PR China. Electronic address:
Chronic wounds caused by microbial infection have emerged as a major challenge on patients and medical health system. Bacterial cellulose (BC) characterized by its excellent biocompatibility and porous network, holds promise for addressing complex wound issues. However, lack of inherent antibacterial activity and cross-linking sites in the molecular network of BC have constrained its efficacy in hydrogel design and treatment of bacterial-infected wounds.
View Article and Find Full Text PDFA Wenzel Interfaces Design for Homogeneous Solute Distribution Obtains Efficient and Stable Perovskite Solar Cells.
Adv Mater
January 2025
College of Chemistry and Chemical Engineering/Film Energy Chemistry for Jiangxi Provincial Key Laboratory (FEC), Nanchang University, 999 Xuefu Avenue, Nanchang, 330031, China.
The coffee-ring effect, caused by uneven deposition of colloidal particles in perovskite precursor solutions, leads to poor uniformity in perovskite films prepared through large-area printing. In this work, the surface of SnO is roughened to construct a Wenzel model, successfully achieving a super-hydrophilic interface. This modification significantly accelerates the spreading of the perovskite precursor solution, reducing the response delay time of perovskite colloidal particles during the printing process.
View Article and Find Full Text PDFRunning-In Behavior and Failure Mechanism Between AgCuNi Alloy and Au-Electroplated Layer.
Sensors (Basel)
December 2024
State Key Laboratory of Tribology in Advanced Equipment, Tsinghua University, Beijing 100084, China.
To avoid wear and tear of the slip ring due to electrical corrosion, the slip ring needs to undergo the running-in process under atmospheric conditions without current after assembly. To address the urgent demand for long-service capability space conductive slip rings in the aerospace field, the running-in behavior and failure mechanism between the AgCuNi alloy and Au-electroplated layer are investigated using a ball-on-disc tribometer in this paper. The results show that the transfer film composed of Au plays an important role in modifying the friction during the sliding process.
View Article and Find Full Text PDFExploration of Optical Fiber and Laser Cutting Head Applications in High-Radiation Environments for Fast Reactor Spent Fuel Reprocessing.
Sensors (Basel)
December 2024
China Institute of Atomic Energy, P.O. Box 275 (26), Beijing 102413, China.
Fast-neutron reactors are an important representative of Generation IV nuclear reactors, and due to the unique structure and material properties of fast reactor fuel, traditional mechanical cutting methods are not applicable. In contrast, laser cutting has emerged as an ideal alternative. However, ensuring the stability of optical fibers and laser cutting heads under high radiation doses, as well as maintaining cutting quality after irradiation, remains a significant technical challenge.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!