This study evaluated effects of differing gel volumes on pharmacokinetics (PK). IQB4012, a gel containing the non-nucleoside reverse transcriptase inhibitor IQP-0528 and tenofovir (TFV), was applied to the pigtailed macaque vagina and rectum. Vaginal gel volumes (1% loading of both drugs) were 0.5 or 1.5 ml; following wash-out, 1 or 4 ml of gel were then applied rectally. Blood, vaginal, and rectal fluids were collected at 0, 2, 4, and 24 h. Vaginal and rectal tissue biopsies were collected at 4 and 24 h. There were no statistically significant differences in concentrations for either drug between gel volumes within compartments at matched time points. After vaginal gel application, median IQP-0528 concentrations were ~ 10-10 ng/g, 10-10 ng/ml, and 10-10 ng/ml in vaginal tissues, vaginal fluids, and rectal fluids, respectively (over 24 h). Median vaginal TFV concentrations were 1-2 logs lower than IQP-0528 levels at matched time points. After rectal gel application, median IQP-0528 and TFV concentrations in rectal fluids were ~ 10-10 ng/ml and ~ 10-10 ng/ml, respectively. Concentrations of both drugs sampled in rectal tissues were low (~ 10-10 ng/g). For 1 ml gel, half of sampled rectal tissues had undetectable concentrations of either drug, and over half of sampled rectal fluids had undetectable TFV concentrations. These results indicate differences in drug delivery between the vaginal and rectal compartments, and that smaller vaginal gel volumes may not significantly compromise microbicide PK and prophylactic potential. However, effects of rectal gel volume on PK for both drugs were less definitive.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6711467PMC
http://dx.doi.org/10.1007/s13346-018-0538-0DOI Listing

Publication Analysis

Top Keywords

vaginal rectal
16
gel volumes
16
rectal fluids
16
vaginal gel
12
tfv concentrations
12
sampled rectal
12
rectal
11
gel
11
vaginal
10
gel volume
8

Similar Publications

Application value of personalized 3D printing vaginal model for the Image-guided adaptive brachytherapy of cervical cancer.

J Gynecol Oncol

November 2024

The 3th Ward of Radiotherapy Department, Guangzhou Institute of Cancer Research, The Affiliated Cancer Hospital, Guangzhou Medical University, Guangzhou, China.

Objective: To explore the application value of using 3-dimensional (3D) printing (3DP) technology to create individualized vaginal molds for brachytherapy (BT) in high-dose-rate 3D cervical cancer through reverse engineering of needle placement.

Methods: Prospectively, 11 patients with cervical cancer were treated with 3DP-intracavitary/interstitial (IC/IS) BT using 3DP to create individualized vaginal molds. All patients were performed BT after completion of external beam radiotherapy (EBRT).

View Article and Find Full Text PDF

Purpose: To present an innovative deformable applicator that used Freiburg flap as vaginal applicator with or without free-hand interstitial needles in three-dimensional (3D) high-dose-rate (HDR) brachytherapy for vaginal stump recurrence of cervical cancer.

Material And Methods: Between September 2017 and January 2020, all patients with vaginal stump recurrence after radical hysterectomy of cervical cancer treated with vaginal stump brachytherapy using Freiburg flap as vaginal applicator with or without free-hand interstitial needles were retrospective analyzed. Characteristics related to patients and treatment modality as well as preliminary outcomes and side effects were investigated.

View Article and Find Full Text PDF

Purpose: The purpose of the study was to analyze patients with vaginal-involving recurrences of gynecological tumors and primary vaginal tumors, treated with transperineal interstitial brachytherapy (P-ISBT). Dosimetric, clinical, and toxicity analysis of these patients was conducted, incorporating MRI in volume definition and dose-volume dosimetry.

Material And Methods: Forty-two patients were retrospectively analyzed.

View Article and Find Full Text PDF

Cutaneous metastases from rectal adenocarcinoma: A case report.

SAGE Open Med Case Rep

December 2024

Department of Medicine, University of Alberta, Edmonton, AB, Canada.

Cutaneous metastases from colorectal cancer are an uncommon but critical finding, typically signaling advanced disease with poor prognosis. This case report describes a 64-year-old woman with a limited past medical history who presented to our outpatient dermatology practice with rapidly spreading erythematous, indurated, and nearly verruciform plaques in the groin, vaginal, and perineal region. Biopsy confirmed metastatic adenocarcinoma of colonic origin, and diagnostic imaging, and colonoscopy revealed stage IV colorectal cancer involving extensive cutaneous, lymphatic, and visceral metastases.

View Article and Find Full Text PDF

3D printing of pharmaceutical dosage forms: Recent advances and applications.

Adv Drug Deliv Rev

December 2024

Heinrich Heine University Düsseldorf, Faculty of Mathematics and Natural Sciences, Institute of Pharmaceutics and Biopharmaceutics, Universitätsstraße 1, 40225 Düsseldorf, Germany; Freie Universität Berlin, Institute of Pharmacy, Pharmaceutical Technology, Kelchstraße 31, 12169 Berlin, Germany. Electronic address:

Three-dimensional (3D) printing, also referred to as additive manufacturing, is considered to be a game-changing technology in many industries and is also considered to have potential use cases in pharmaceutical manufacturing, especially if individualization is desired. In this review article the authors systematically researched literature published during the last 5 years (2019 - spring 2024) on the topic of 3D printed dosage forms. Besides all kinds of oral dosage forms ranging from tablets and capsules to films, pellets, etc.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!