The paper describes a novel laser ultrasonic profilometry method which uses pulsed laser radiation for imaging of the surface profile of solid objects in optically opaque liquids by scattering of ultrasonic waves. Algorithms for the construction of laser ultrasonic images and for profile segmentation are presented. An experimental setup for profile measurements is described. It allows reconstructing of laser ultrasonic images with a frame rate of 10 Hz and performing an automated 3D scanning of samples. The results of the experimental testing of laser ultrasonic profilometry on duralumin samples are presented. The approximation error of duralumin cylinder surface profile measurements in water is 15 μm. The results are compared to those obtained by x-ray tomography.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/AO.57.000C70 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Assessment of Corrosion and Cavitation Resistance of Laser Remelted GX40CrNiSi25-20 Cast Stainless Steel.
Materials (Basel)
December 2024
Department of Materials and Fabrication Engineering, Politehnica University Timisoara, Bulevardul Mihai Viteazul nr.1, 300222 Timișoara, Romania.
This paper explores the enhancement of cavitation and corrosion resistance in cast stainless steel through laser beam surface remelting. The influence of laser treatment on material properties was assessed by analyzing the microstructure using optical microscopy, electron microscopy, and X-ray diffraction. Cavitation erosion was evaluated in tap water using an ultrasonic vibration setup, following ASTM G32-2016 standards.
View Article and Find Full Text PDFDevelopment of a photoacoustic acquisition system and their proof-of-concept for hemoglobin detection.
Heliyon
January 2025
Center for MicroElectromechanical Systems (CMEMS), University of Minho, Guimarães, 4800-058, Portugal.
Recently, Organ-on-a-Chip (OoC) platforms have arisen as an increasingly relevant experimental tool for successfully replicating human physiology and disease. However, there is a lack of a standard technology to monitor the OoC parameters, especially in a non-invasive and label-free way. Photoacoustic (PA) systems can be considered an alternative and accurate assessment method for OoC platforms.
View Article and Find Full Text PDFFabrication of novel pullulan/carboxymethyl chitosan-based edible film incorporated with ultrasonically equipped aqueous zein/turmeric essential oil nanoemulsion for effective preservation of mango fruits.
Int J Biol Macromol
January 2025
School of Food and Biological Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013, China. Electronic address:
This study aimed to develop ultrasonically-assisted, alcohol-free, and noncorrosive aqueous zein/turmeric essential oil (TEO)-loaded nanoemulsions (NEs) to stimulate pullulan/carboxymethyl chitosan (P/CMCS)-based edible films for mango fruit preservation. The influence of innovative sonicated zein/TEO-based NEs (ZTNEs) as nanofillers on the physico-mechanical characteristics of the resulting P/CMCS edible films was investigated. A stable and well-dispersed ZTNE was achieved using 20 % zein with 10 min of ultrasound treatment, leading to a reduced droplet size (194.
View Article and Find Full Text PDFQuantitative evaluation of corrosion-thinning defect by an instantaneous wavenumber multi-shot fusion method based on laser ultrasonic guided wavefield detection.
Ultrasonics
December 2024
Faculty of Information Technology, Beijing University of Technology, Beijing, China.
The thickness loss caused by corrosion is a vital factor that threatens the health of shell structures. It is significant to perform a non-destructive quantitative evaluation of corrosion-thinning defects in plate structures. Based on the laser ultrasonic guided wavefield scanning technology, this paper proposes an instantaneous wavenumber multi-shot fusion method, which improves the performance of the instantaneous wavenumber imaging method.
View Article and Find Full Text PDFThe effect of Er:YAG laser irradiation with different frequencies on surface decontamination of used healing abutments: a supplementary approach to sterilization.
Lasers Med Sci
December 2024
Department of Periodontics, Faculty of Dentistry, Tehran Medical Sciences, Islamic Azad University, Tehran, Tehran, Iran, Islamic Republic of.
Reusing healing abutments is common practice among clinicians; however, ensuring complete surface decontamination is crucial to avoid further complications. This study aimed to evaluate the cleaning potential of Er: YAG laser at different frequencies, as an adjunctive step prior to autoclave sterilization. Forty contaminated healing abutments were divided into four groups.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!