The titanium opaque porcelain was synthesized through sol-gel using borate-silicate system. The porcelain was characterized by DSC-TG, X-ray diffraction, N adsorption-desorption isotherms and scanning electron microscope tests. The results of DSC showed that the nitrates could be decomposed completely when the bioglass xerogel precursor was heat-treated at 760 ℃. The XRD results showed that the NaCaSiO was the major phase of the opaque porcelain. The synthesized opaque porcelain powders had an average particle size of about 5-25 µm with nanopores of around 50-70 nm on the surface. The BET average surface area of the porcelain was 12.67 m/g, while the average pore diameters for adsorption and desorption were 9.73 and 10.16 nm, respectively. The flexure strength significantly increased from 47.4 MPa to 116.2 MPa with the sintering temperature increasing from 575 ℃ to 600 ℃. The XRD, FTIR and EDS results proved that hydroxyapatite had formed on the porcelain surface after incubation in simulated body fluid.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.jmbbm.2018.04.005 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Marginal Accuracy of Ceramic Veneer Alloy Related to Different Alloy Fabrication Techniques, Ceramic Veneering Methods, Stages, and Sites of Fabrication.
Eur J Dent
November 2024
Division of Pediatric Dentistry, Department of Preventive Dentistry, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand.
Objectives: Fabrication processes affect accuracy of restoration. This study compared marginal accuracy of ceramic veneer metal upon different metal substructure fabrication techniques, ceramic veneering methods, stages, and sites of restoration.
Material And Methods: A prepared premolar metal abutment was used to fabricate 96 metal substructures from 4 techniques: cast metal with traditionally impressed tooth (CmTt), cast metal with digitally milled wax (CmDw), sintered metal with digitally impressed tooth (SmDt), and sintered metal with digitally impressed stone model (SmDm).
Effects of porcelain layer thickness and luting resin cement on the opalescence properties of porcelain veneers.
BMC Oral Health
October 2024
Department of Prosthodontics, Kunming Medical University School and Hospital of Stomatology, No 1088, Haiyuan Road, Kunming, China.
Article Synopsis
- The study investigates how the thickness of porcelain veneers and the type of luting resin affect the opalescence of veneers used for discolored teeth.
- Ninety porcelain veneer specimens were created and grouped based on the type of porcelain and whether resin cement was applied, with varying thicknesses analyzed using statistical methods.
- Results showed that thicker veneer layers and the inclusion of opaque materials significantly enhanced the opalescence of the restorations, indicating a positive correlation between thickness and aesthetic performance.
Impact of Battery Levels of a Cordless LED Curing Unit on Resin Cement under Varied Lithium Disilicate Thicknesses and Translucencies.
Oper Dent
November 2024
*Luís Henrique Araújo Raposo, DDS, MSc, PhD, associate professor, Department of Occlusion, Fixed Prosthodontics and Dental Materials, School of Dentistry, Federal University of Uberlândia, MG, Brazil.
Objectives: This study aimed to evaluate the impact of battery levels on the emission of a multi-peak cordless LED light-curing unit (LCU) and the effect on the degree of conversion (DC) and Knoop hardness (KH) of a light-cure resin luting agent activated through varying lithium disilicate (LiS2) ceramic thicknesses and translucencies.
Methods: High and low translucency LiS2 discs (IPS e.max Press HT and LT, respectively; shade A1) with thickness of 0.
Evaluating the Impact of Oxidation Heat Treatment and Dual Opaquing Techniques on Enhancing Metal-Ceramic Bond Strength.
Cureus
September 2024
Oral and Maxillofacial Surgery, Rajasthan Dental College and Hospital, Jaipur, IND.
Article Synopsis
- The research investigates how oxidation heat treatment (OHT) and dual opaquing techniques affect the bond strength between metal and ceramic in dental materials.
- Eighty samples were created, divided into two main groups based on oxidation treatment, and further categorized by single or double layers of opaque porcelain, followed by flexural strength testing.
- Results showed that the combination of OHT and double layering (group A2) resulted in the highest bond strength, highlighting the significance of these techniques in enhancing ceramo-metal restorations.
The effect of photoinitiator type and filler load on physicochemical and mechanical properties of experimental light-cured resin cements through lithium disilicate ceramics of different shades and thicknesses.
Dent Mater
September 2024
Biomaterials Unit, School of Dentistry, College of Medical and Dental Sciences, University of Birmingham, Birmingham B4 6NN, UK.
Objective: This study investigated the influence of photoinitiator types on degree of conversion (DC), rate of polymerization (RP), flexural strength (FS), flexural modulus (FM), and light transmittance (LT) of filled and unfilled light-curable resin cements through different thicknesses and shades of lithium disilicate ceramics.
Methods: Lithium disilicate ceramic discs (IPS Emax Press, background [0.0], 0.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!