Aim: The aim of the present study was to determine the degree of surface staining and roughness of resin composites (RC) after finishing and polishing with different methods and immersion in three soft drinks.
Methods: A microhybrid, a nanohybrid, and a hybrid composite were selected. The specimens were prepared and divided into three groups of 36 after 24 hours, and designated as either unpolished or polished using Sof-Lex discs or Enhance point. Each group was further divided into three subgroups, immersed in distilled water, coffee, or cola for 1 week (N = 12). Color change (∆E) was measured by a spectrophotometer after each treatment. The ∆E was calculated using the following formula: ∆E = ([∆L]2+[∆a]2+[∆b]2)1/2. Surface roughness (Ra) was measured after 24 hours and 1 week. To observe the Ra, a scanning electron microscope was used.
Results: A moderate correlation between Ra and ∆E was determined. Only coffee caused perceptible ∆E. The effect of Ra on staining was statistically significant (P < .05), but immersion in solutions for 7 days did not increase the Ra of RC.
Conclusions: The highest Ra values were obtained from hybrid RC. The Enhance point created the greatest roughness. Coffee was associated with the greatest ∆E for all materials and polishing methods.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/jicd.12333 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Antimicrobial Activity of UV-Activated and Cysteamine-Grafted Polymer Foils Against Bacteria and Algae.
Polymers (Basel)
January 2025
Centre for Nanomaterials and Biotechnology, Faculty of Science, University of Jan Evangelista Purkyně, Pasteurova 15, 400 96 Ústí nad Labem, Czech Republic.
Surface modification of various polymer foils was achieved by UV activation and chemical grafting with cysteamine to improve surface properties and antimicrobial efficacy. UVC activation at 254 nm led to changes in surface wettability and charge density, which allowed the introduction of amino and thiol functional groups by cysteamine grafting. X-ray photoelectron spectroscopy (XPS) confirmed increased nitrogen and sulfur content on the modified surfaces.
View Article and Find Full Text PDFA Preliminary Stability Assessment of Three State-of-the-Art CAD/CAM Materials Under Human Gingival Cell Culture.
Polymers (Basel)
January 2025
Plasma and Radiation Physics, National Institute for Laser, 077125 Magurele, Romania.
CAM/CAD composites are widely used as dental restoration materials due to their resistivity to wear. The purpose of this study was to determine the effect of human gingival fibroblast cells on three different computer-aided design/computer-aided manufacturing (CAD/CAM) hybrid materials with resin-based composites (RBC) and to assess their stability following cell growth. The CAM/CAD dental materials were investigated in different conditions as follows: (i) cells (human gingival fibroblasts, HFIB-Gs) incubated over the material for each sample, denoted as A; (ii) reference, the raw material, denoted as B; and (iii) materials incubated in DMEM medium, denoted as C.
View Article and Find Full Text PDFActive Polylactide-poly(ethylene glycol) Films Loaded with Olive Leaf Extract for Food Packaging-Antibacterial Activity, Surface, Thermal and Mechanical Evaluation.
Polymers (Basel)
January 2025
Department of Cosmetic and Biomaterials Chemistry, Faculty of Chemistry, Nicolaus Copernicus University in Toruń, Gagarina 7, 87-100 Toruń, Poland.
As the demand for sustainable and innovative solutions in food packaging continues to grow, this study endeavors to introduce a comprehensive exploration of novel active materials. Specifically, we focus on characterizing polylactide-poly(ethylene glycol) (PLA/PEG) films filled with olive leaf extract (OLE; ) obtained via solvent evaporation. Examined properties include surface structure, thermal degradation and mechanical attributes, as well as antibacterial activity.
View Article and Find Full Text PDFSuperhydrophobic Coatings Based on PMMA-Siloxane-Silica and Modified Silica Nanoparticles Deposited on AA2024-T3.
Polymers (Basel)
January 2025
Jožef Stefan Institute, Department of Physical and Organic Chemistry, Jamova c. 39, SI-1000 Ljubljana, Slovenia.
The study aimed to develop a superhydrophobic coating on the aluminium alloy 2024-T3 surface. The desired surface roughness and low surface energy were achieved with SiO nanoparticles, synthesised via the Stöber method and modified with alkyl silane (AS) or perfluoroalkyl silane (FAS). To enhance particle adhesion to the alloy substrate, nanoparticles were incorporated into a hybrid sol-gel coating composed of tetraethyl orthosilicate, methyl methacrylate, and 3-methacryloxypropyl trimethoxysilane.
View Article and Find Full Text PDFAcylase-Based Coatings on Sandblasted Polydimethylsiloxane-Based Materials for Antimicrobial Applications.
Polymers (Basel)
January 2025
Center for Micro-Electro Mechanical Systems (CMEMS), Campus Azurém, University of Minho, 4800-058 Guimarães, Portugal.
Indwelling medical devices, such as urinary catheters, often experience bacterial colonization, forming biofilms that resist antibiotics and the host's immune defenses through quorum sensing (QS), a chemical communication system. This study explores the development of antimicrobial coatings by immobilizing acylase, a quorum-quenching enzyme, on sandblasted polydimethylsiloxane (PDMS) surfaces. PDMS, commonly used in medical devices, was sandblasted to increase its surface roughness, enhancing acylase attachment.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!