Purpose Most of the studies concerning gellan have been focused on its application as a food ingredient, however, gellan is often considered as a candidate for the development of novel pharmaceutical formulations. Taking into account that gellan is ion-sensitive, it can be assumed that its initial mechanical properties can change upon contact with body secretions. Therefore, the aim of the work was to investigate the rheological properties of pure high-acyl gellan gum hydrogel (0.4%) and its mixtures with selected simulated body fluids. Methods The rheological investigations were performed on rotational rheometer and included oscillatory temperature, amplitude, and frequency sweeping. The results enabled estimation of the linear viscoelastic regime, calculation of the cross-over points, and percentage of structure recovery. Results In the case of pure hydrogel no evidence of thermosensitivity was observed in the range of 20-40°C. In pH = 1.2 (NaCl/HCl) the hydrogel structure was almost entirely destroyed. Mixing with phosphate buffer (pH = 4.5) resulted in higher gel strength than after dilution with deionized water. The opposite effect was observed in the case of pH = 7.4. The studies performed for the mixture of GG hydrogel and mucin indicated interaction between the components. The hydrogel elasticity increased in the presence of simulated tear, but decreased in simulated saliva and vaginal fluid. Conclusions In this study, it was shown that the stability of a three-dimensional gellan structure may be affected by pH and the presence of mucin which most probably competed with gellan gum in divalent cations binding. The observations presented in this study may be important in terms of potential application of gellan gum as a potential carrier in drug delivery systems.

Download full-text PDF

Source
http://dx.doi.org/10.1177/0885328218762361DOI Listing

Publication Analysis

Top Keywords

gellan gum
16
gellan
8
high-acyl gellan
8
gum hydrogel
8
simulated body
8
body fluids
8
hydrogel
6
rheological investigation
4
investigation high-acyl
4
gum
4

Similar Publications

To improve wound healing, advanced biofabrication techniques are proposed here to develop customized wound patches to release bioactive agents targeting cell function in a controlled manner. Three-dimensional (3D) bioprinted "smart" patches, based on methacrylated gellan gum (GGMA), loaded with tannic acid (TA) or L-ascorbic acid (AA) have been manufactured. To improve stability and degradation time, gellan gum (GG) was chemically modified by grafting methacrylic moieties on the polysaccharide backbone.

View Article and Find Full Text PDF

Innovative packaging materials are essential for preserving food, serving as a substitute for petroleum-based options. In this study, biofilms consisting of pullulan and gellan gum which incorporates astaxanthin nanoemulsion were prepared to extend the shelf-life of strawberries. Hydrophobic deep eutectic solvents (DES) were used as solvents to extract natural astaxanthin from Haematococcus pluvialis.

View Article and Find Full Text PDF

3D-printed ultra-sensitive strain sensors using biogels prepared from fish gelatin and gellan gum.

Carbohydr Polym

March 2025

Engineering Research Centre of Fujian-Taiwan Special Marine Food Processing and Nutrition (Ministry of Education), Fujian Agriculture and Forestry University, Fuzhou 350002, China; College of Food Science, Fujian Agriculture and Forestry University, Fuzhou 350002, PR China; China-Ireland International Cooperation Centre for Food Material Science and Structural Design, Fuzhou 350002, China. Electronic address:

The long-term sustainable development of flexible electronic devices is limited by a reliance on synthetic polymers that pose dangers for humans and potentially severe ecological problems, as well as a reliance on conventional processing methods. This work aims to exploit 3D printing to develop natural biogels composed of fish gelatin and high acyl gellan gum for use as flexible sensors. The electrical conductivity and mechanical strength were remarkably enhanced through the environmentally friendly enzyme (transglutaminase) cross-linking and non-toxic ethanol modification treatment, which allows the development of 3D printed sensors for temperature, strain, and stress sensors.

View Article and Find Full Text PDF

This paper investigated the effects of heating and pH on the stability of emulsions of non-covalent complexes of gellan gum (GG) and soy protein isolate (SPI). As a result, the GG-SPI complexes stabilized emulsion exhibited a minimum emulsion particle size (945 ± 23 nm), a maximum absolute values of zeta-potential (-32.7 ± 0.

View Article and Find Full Text PDF

In this study, pH-responsive nanocomposite films with high barrier properties were obtained by the addition of a mixture of methyl red and bromothymol blue to the inner film and Silicon dioxide nanoparticles (nano-SiO) to the outer film matrix. The incorporation of nano-SiO resulted in a notable reduction in the oxygen permeability coefficient and water vapor transmission rate, accompanied by an enhancement in the UV barrier and tensile strength. In comparison with the control sample (0 % nano-SiO), the film containing 1 % nano-SiO exhibited a 57.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!