We evaluated the effect of different curing strategies for universal adhesives on micro-tensile bond strength (μTBS) between resin cement and dentin and/or between resin cement and indirect resin composite. Flat coronal dentin surfaces and composite resin disks were pretreated with silane-containing universal adhesives, with or without light-curing on the dentin-side and/or composite resin disk-side. Resin disks were luted onto the pretreated dentin surfaces with the corresponding dual-cure adhesive resin cements and light-cured, and cut into beams after 24-h water storage. After 0 or 10,000 thermocycles (5ºC/55ºC) in a water bath, the μTBS of the composite resin disk-dentin beam was tested. The μTBS was highest when universal adhesives were applied to both the dentin- and the indirect composite resin disk-side, followed by light-curing. Thermocycling decreased μTBS in all but the Scotchbond Universaltreated group, with light-curing on both sides. The effect of curing strategies is dependent upon the materials.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.4012/dmj.2017-240 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
[Preparation and methodological analysis of chitosan-based ultrasound-coupled hydrogel pads].
Sheng Wu Gong Cheng Xue Bao
December 2024
The College of Life Sciences, Northwest University, Xi'an 710069, Shaanxi, China.
This study aims to optimize the process for preparing chitosan-based ultrasound-coupled hydrogel pads and investigate their application potential in ultrasonography. Chitosan, 2-acrylamido-2-methylpropanesulfonic acid, and N-isopropylacrylamide were used as the main materials to prepare chitosan-based ultrasound-coupled hydrogel pads. The free-radical polymerization conditions were optimized by a three-factor, three-level orthogonal test with the tensile strength and ultrasound image quality of the hydrogel pads as evaluation indicators.
View Article and Find Full Text PDFEvaluation of the shear bond strength of surface-treated Cobalt-Chromium metal crowns on corticobasal® implant abutments cemented using different luting agents.
J Stomatol Oral Maxillofac Surg
December 2024
Reader, Department of Periodontics, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai 600077, Tamil Nadu, India.. Electronic address:
Purpose: This in-vitro study aimed to compare the shear bond strength (SBS) of cobalt-chromium (Co-Cr) crowns on Corticobasal® implant abutments, evaluating the effects of two surface treatments and two luting agents.
Materials And Methods: Thirty Co-Cr crowns were fabricated using CAD-CAM technology with a direct metal laser sintering process and divided into three groups based on surface treatment: Group I (untreated), Group II (sandblasted with 50 μm Al₂O₃), and Group III (Er: YAG laser etching). Each group was further subdivided based on luting cement: Sub group A (GC Fuji Plus) and Sub group B (Rely X U200).
A comprehensive study on MDP effects: Microshear bond strength and fatigue resistance in 4YSZ ceramics.
Braz Dent J
December 2024
Post-Graduate Program in Oral Sciences (Prosthodontics Unit), Faculty of Dentistry, Federal University of Santa Maria (UFSM), Santa Maria, Rio Grande do Sul, Brazil.
The aim of this study is to assess the presence of MDP at various stages of the bonding procedure, enhance the adhesive and mechanical behavior of cemented zirconia ceramics. Fifty ceramic slices (15 × 15 × 2 mm) and 48 discs (Ø= 10 mm, 1 mm thickness) were prepared, sintered, air-abraded with aluminum oxide, and allocated considering: 1) microshear bond strength (µSBS) between ceramic slices and luting agent cylinders (height= 1 mm, Ø= 1.2 mm); 2) fatigue behavior, ceramic discs paired and bonded onto fiber-epoxy resin discs (Ø= 10 mm, 2.
View Article and Find Full Text PDFEffect of argon plasma and dentin rehydration on bond strength of dental adhesives to etched dentin.
Braz Dent J
December 2024
Department of Restorative Dentistry. Piracicaba Dental School, University of Campinas, Brazil.
This study investigated the effects of nonthermal atmospheric pressure plasma (NAPP) application and dentin rehydration with water (REHY) on bond strength (BS) of adhesives. Three etch-and-rinse adhesives were tested: Scotchbond Multi-Purpose (SBM / water-based primer + adhesive resin), Gluma Bond Universal (GBU / single-bottle containing acetone as organic solvent) and Prime&Bond Universal (PBU / single-bottle containing propanol as organic solvent). Adhesives were applied: 1- to phosphoric acid-etched dentin (Control), 2- after NAPP application for 45 seconds to etched dentin or 3- after REHY with water (10 seconds) of plasma-treated etched dentin.
View Article and Find Full Text PDFAssessing shear bond strength of various surface treatments of 3D-printed provisional material with bis-acryl relining material.
BMC Oral Health
December 2024
Division of Prosthodontics, Faculty of Dentistry, Thammasat University, Pathum Thani, 12120, Thailand.
Objective: Marginal adaptation of the provisional restoration often requires relining from relining materials. This study determined the effects of surface treatments on the shear bond strength (SBS) between 3D-printed provisional and bis-acryl relining materials.
Materials And Methods: The 3D-printed provisional specimens (9 × 9 × 2 mm) were prepared using methacrylate-based material.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!