We present a theoretical model for the thermal effect of the fiber coating on a high-power cladding light stripper, which is fabricated by chemical etching. For the input and output of the fiber coating, a novel segmented corrosion method and increasing attenuation method are proposed for heat suppression, respectively. The relationship between the attenuation and temperature rise of the fiber coating at the output is experimentally demonstrated. The temperature distribution of the fiber coating at the input as well as the return light power caused by scattering are measured for the etched fiber with different surface roughness values. The results suggest that the rise in temperature is primarily caused by the scattering light propagating into the coating. Finally, an attenuation of 27 dB is achieved. At a room temperature of 23°C and input pump power of 438 W, the highest temperature of the input fiber coating decreases from 39.5°C to 27.9°C by segmented corrosion, and the temperature rise of the output fiber coating is close to 0.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/AO.57.000485 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Machine learning-enhanced detection of chlorpyrifos using molecularly imprinted polymer-coated optical fibers.
Talanta
January 2025
Department of Physics, Institute of Science, Banaras Hindu University, Varanasi, 221005, India. Electronic address:
This paper explores the use of large core declad optical fibers coated with molecularly imprinted polymers for chlorpyrifos detection, a key marker of organophosphate pesticides. The performance of sensor is evaluated using artificial neural networks and principal component analysis. By varying the declad length, the performance of molecularly imprinted polymer-coated fibers is compared to uncoated fibers, and both are used to identify commercial and pure samples of chlorpyrifos pesticides.
View Article and Find Full Text PDFHigh-Density Polyethylene Janus Fibrous Membrane with Enhanced Breathability and Moisture Permeability via PDA Assisted Hydrophilic Modification.
Macromol Rapid Commun
January 2025
State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai, 201620, China.
Functional fibrous membranes with high mechanical properties are intensively developed for different application fields. In this study, to enhance moisture and air permeability without compromising mechanical strength, a facile float-surface modification strategy is employed to fabricate Janus fibrous membranes with distinct hydrophobicity/hydrophilicity using the high-density polyethylene (HDPE) fibrous membranes. By coating one side of the HDPE fibrous membranes with polydopamine (PDA) and a superhydrophilic polyelectrolyte, the obtained Janus HDPE fibrous membranes demonstrate an excellent water transmission rate (577.
View Article and Find Full Text PDFDesign optimization of a 1-D array of stemless plastic scintillation detectors.
Med Phys
January 2025
Department of Physics and Atmospheric Science, Dalhousie University, Halifax, Nova Scotia, Canada.
Background: A stemless plastic scintillation detector (SPSD) is composed of an organic plastic scintillator coupled to an organic photodiode. Previous research has shown that SPSDs are ideally suited to challenging dosimetry measurements such as output factors and profiles in small fields. Lacking from the current literature is a systematic effort to optimize the performance of the photodiode component of the detector.
View Article and Find Full Text PDFQuasi-Simultaneous and Automated Measurement of Primary Amines and Short-Chain Aldehydes Emission by Dynamic SPME On-Fiber Derivatization Coupled With a Flow-Cell.
J Sep Sci
January 2025
Dow Chem (China) Invest Co. Ltd., Shanghai, China.
An automated method was developed to simultaneously measure primary amines and short-chain aldehydes emission from foam and rubber samples in one experiment. The technique involved dynamic solid-phase microextraction (SPME) on-fiber derivatization coupled with a flow-cell unit. The parameters of the dynamic SPME on-fiber derivatization method were optimized, including SPME coating, derivatization agents loading temperature, loading time, and dynamic SPME extraction time.
View Article and Find Full Text PDFCellular EMT-status governs contact guidance in an electrospun TACS-mimicking model.
Mater Today Bio
February 2025
Pharmaceutical Technology and Biopharmaceutics, Department of Pharmacy, Ludwig-Maximilians-University München, Munich, Germany.
In this study, an advanced nanofiber breast cancer model was developed and systematically characterized including physico-chemical, cell-biological and biophysical parameters. Using electrospinning, the architecture of tumor-associated collagen signatures (TACS5 and TACS6) was mimicked. By employing a rotating cylinder or static plate collector set-up, aligned fibers (TACS5-like structures) and randomly orientated fibers (TACS6-like structures) fibers were produced, respectively.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!