Introduction: We describe our experience of cranioplasty after a calvarial defect, following an external decompressive craniectomy, with the Medpor (Stryker) porous polyethylene implant for cosmetic cranioplasty and reconstruction.
Methods: A retrospective chart review was performed on 23 consecutive patients who underwent cranioplasty at a single institution between January 2013 and January 2016: 9 patients after head injury and 14 patients after vascular event (ruptured aneurysm, intraprenchymal haematoma, malignant cerebrovascular accident). All patients with cranioplasties after oncological resection or infection were excluded. These cranioplasties were performed using porous polyethylene sheet (Medpor) and contoured with a burr or scissors in the sterile field, and fixed to the calvarial bone with screws.
Results: Porous polyethylene sheet (Medpor) is a proven material used for cranial reconstruction in neurosurgery and maxillofacial surgery with a biocompatibility advantage. The implant can be directly used in an emergency context. The average operating time was 72minutes. An average delay of 527 days (1 year and 5months) with a median of 985 days (43; 4206) occurred between craniectomy and the cranioplasty. There was only one set back implant due to scalp necrosis with infection for a recovery-unit patient.
Conclusion: Porous polyethylene is an excellent restorative material for the reconstruction of large sized cranial defects and can be also used safely in reconstruction of the cranium. The cosmetic results are good, easy to perform, with a low complication rate.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.neuchi.2017.07.001 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Expanding access to maggot containment dressings through redesign and innovation.
Int Wound J
January 2025
Applied BioSciences, Faculty of Science and Engineering, Macquarie University, North Ryde, New South Wales, Australia.
There are two major styles of maggot debridement dressings: (1) confinement dressings that form a cage around the wound, and (2) containment dressings that completely surround the maggots within a sealed porous bag. For producers and clinicians wanting to prepare containment dressings using readily available polyester bags, it is currently difficult to seal these bags without expensive high-temperature plastic welders. This study aimed to identify simple and affordable methods for sealing maggots within polyester net bags.
View Article and Find Full Text PDFMicroporous carbon derived from waste plastics for efficient adsorption of tetracycline: Adsorption mechanism and application potentials.
Environ Res
January 2025
MIIT Key Laboratory of Critical Materials Technology for New Energy Conversion and Storage, School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, China.
In recent years, the accumulation of waste plastics and emergence plastic-derived pollutants such as microplastics have driven significantly the development and updating of waste plastic utilization technology. This study prepared the porous carbon (PC-1-KOH) material directly from polyethylene terephthalate (PET) in waste plastic bottles using KOH activation and molten salt strategy for efficient removal of antibiotic tetracycline (TC). The maximum removal efficiency of TC was 100.
View Article and Find Full Text PDFEffects of Relative Microplastic-Biochar Sizes and Biofilm Formation on Fragmental Microplastic Retention in Biochar Filters.
Environ Res
January 2025
Department of Environmental and Sustainable Engineering, Faculty of Engineering, Chulalongkorn University, 254 Phayathai Road, Pathumwan, Bangkok, 10330, Thailand; Professor Aroon Sorathesn Center of Excellence in Environmental Engineering, Department of Environmental and Sustainable Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, 10330, Thailand. Electronic address:
Microplastics (MPs) pose significant risks to aquatic life and human health. Conventional water treatment is ineffective in removing MPs, demanding alternative technologies. Biochar exhibits a potential for removing MPs through adsorption and filtration.
View Article and Find Full Text PDFRegulating Lithium-Ion Transport in PEO-Based Solid-State Electrolytes through Microstructures of Clay Minerals.
ACS Appl Mater Interfaces
January 2025
Research Center of Resource Chemistry and Energy Materials, Key Laboratory of Clay Mineral of Gansu, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, P.R. China.
Clay minerals show significant potential as fillers in polymer composite solid electrolytes (CSEs), whereas the influence of their microstructures on lithium-ion (Li) transport properties remains insufficiently understood. Herein, we design advanced poly(ethylene oxide) (PEO)-based CSEs incorporating clay minerals with diverse microstructures including 1D halloysite nanotubes, 2D Laponite (Lap) nanosheets, and 3D porous diatomite. These minerals form distinct Li transport pathways at the clay-PEO interfaces due to their varied structural configurations.
View Article and Find Full Text PDFCatalysis of a LiF-rich SEI by aromatic structure modified porous polyamine for stable all-solid-state lithium metal batteries.
Chem Sci
January 2025
School of Materials Science and Engineering, Xiangtan University Xiangtan 411105 China
Poly(ethylene oxide) (PEO)-based solid-state polymer electrolyte (SPE) is a promising candidate for the next generation of safer lithium-metal batteries. However, the serious side reaction between PEO and lithium metal and the uneven deposition of lithium ions lead to the growth of lithium dendrites and the rapid decline of battery cycle life. Building a LiF-rich solid electrolyte interface (SEI) layer is considered to be an effective means to solve the above problems.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!