Visibility at airports has to do, in many ways, with flight and ground safety. We present a novel method and algorithms based on lidar measurements and signal noise subtraction to provide atmospheric layering and estimated visibility values for tower controllers and meteorologists as well as from the pilot's point of view, according to the International Civil Aviation Organization and World Meteorological Organization requirements.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/AO.56.006440 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Biocompatibility of variable thicknesses of a novel directly printed aligner in orthodontics.
Sci Rep
January 2025
Department of Orthodontics and Dentofacial Orthopedics, University Medical Center of the Johannes Gutenberg-University Mainz, Augustusplatz 2, 55131, Mainz, Germany.
Direct printed aligners (DPAs) offer benefits like the ability to vary layer thickness within a single DPA and to 3D print custom-made removable orthodontic appliances. The biocompatibility of appliances made from Tera Harz TA-28 (Graphy Inc., Seoul, South Korea) depends on strict adherence to a standardized production and post-production protocol, including UV curing.
View Article and Find Full Text PDFDual-mode natural silk nanofiber aerogel with porous layered structure for highly stabilized radiative cooling and heating.
Int J Biol Macromol
January 2025
School of Chemistry and Materials Science, Hubei Engineering University, Xiaogan 43200, China.
Passive Radiant Cooling and Heating are green and sustainable methods of radiant heat management without consuming additional energy. However, the absorption of sunlight and poor insulation of materials can reduce radiative cooling and also affect radiative heating performance. Herein, we have constructed porous hierarchical dual-mode silk nanofibrous aerogel (SNF) films with high mechanical toughness and stability using silk nanofibers/GO.
View Article and Find Full Text PDFBehavior of YSZ (High YO Content) Layer on Inconel to Electro-Chemical Corrosion.
Materials (Basel)
January 2025
Faculty of Materials Science and Engineering, "Gheorghe Asachi" Technical University of Iasi, 67 Dimitrie Mangeron Street, 700050 Iasi, Romania.
The high yttria content of a stabilized zirconia (YSZ) (38 wt% YO) coating was deposited by atmospheric plasma spraying (APS) from Metco 207 powders on an Inconel 718 (Ni-based superalloy) substrate. As a metal coating connection, a layer of cermet powder (Ni-20% Al-410NS) was used before the ceramic layer deposition. The electro-chemical corrosion resistance of these materials was tested using Inconel cylinders with a diameter of 10 mm and a thickness of 1 mm, with and without the ceramic layer.
View Article and Find Full Text PDFTwenty years of studying the origins and fate of atmospheric mercury over the Mediterranean Sea.
Sci Total Environ
January 2025
CNR-Institute of Atmospheric Pollution Research, Rende Division, UNICAL Polifuzionale, Rende 87036, CS, Italy.
This study provides a review of 13 oceanographic campaigns between 2000 and 2017 to measure Hg in the Mediterranean, highlighting major findings from measurement and modelling activities during the Med-Oceanor program. The initial campaigns showed that high concentrations of RGM could be found far from industrial source regions and the observed daily variation in concentration, with peaks at midday and lower concentrations during darkness gave the first indications that photochemically mediated oxidation reactions were producing RGM in the MBL. Later atmospheric chemistry modelling studies showed the feasibility of Hg oxidation by bromine containing oxidants, which are released as a result of the acidification of sea salt aerosols in the Marine Boundary Layer (MBL).
View Article and Find Full Text PDFLow-Cost Preparation of Wafer-Scale Au(111) Single Crystals for the Epitaxy of Two-Dimensional Layered Materials.
ACS Nano
January 2025
School of Materials Science and Engineering, Peking University, Beijing 100871, People's Republic of China.
Single-crystal Au(111), renowned for its chemically inert surface, long-range "herringbone" reconstruction, and high electrical conductivity, has long served as an exemplary template in diverse fields, , crystal epitaxy, electronics, and electrocatalysis. However, commercial Au(111) products are high-priced and limited to centimeter sizes, largely restricting their broad applications. Herein, a low-cost, high-reproducible method is developed to produce 4 in.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!