Objective: Dentists are facing a myriad of new CAD/CAM product for dental filling therapies. Are the new materials any worthwhile using? Are they succeeding the standard filling materials? Here we compare for the first time the new resin-composite blocks (RCBs) with conventional materials (Filtek Z250 and Tetric EvoCeram).
Methods: The material were tested for residual monomer elution by HPLC, thermogravimetric analysis (TG) was used to determine the percentage of fillers by weight, hardness was evaluated by Vickers method, morphology of fillers and distribution in the matrix were examined by scanning electron microscopy (SEM), elemental analysis for elemental determination of the filler particles was performed by energy-dispersive X-ray spectroscopy (EDX) cytotoxicity using human gingival fibroblasts and an epithelial cell line.
Results: The RBC outperformed conventional composite regarding mechanical characteristics (hardness) and monomer eluation, but showed some worrisome results regarding cytotoxicity.
Significance: The cost benefit is not in favour of RBCs in comparison to conventional composites, as the cytotoxicity was found higher for RBCs.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.dental.2017.09.003 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
3D printing in palliative medicine: systematic review.
BMJ Support Palliat Care
December 2024
Health Research Institute, School of Design, and Confirm Smart Manufacturing Centre, University of Limerick, Limerick, Ireland
Background: Three-dimensional printing (3DP) enables the production of highly customised, cost-efficient devices in a relatively short time, which can be particularly valuable to clinicians treating patients with palliative care intent who are in need of timely and effective solutions in the management of their patients' specific needs, including the relief of distressing symptoms.
Method: Four online databases were searched for articles published by December 2020 that described studies using 3DP in palliative care. The fields of application, and the relevant clinical and technological data were extracted and analysed.
In vitro analysis of composition profiles of resins for 3D printing of dentures.
J Dent
January 2025
Clinic of General-, Special Care- and Geriatric Dentistry, Center for Dental Medicine, University of Zurich, Zurich, Switzerland. Electronic address:
Objective: This study aimed to investigate the resin compounds from CAD-CAM 3D-printed denture resins, focusing on the identification and classification of free monomers and other components. The primary objective was to determine the chemical profile of these 3D-prinding resin materials.
Methods: Four 3D-printed denture resins, two base materials (1: DentaBASE, Asiga Ltd.
Repair bond strength of composite resin to CAD/CAM glass-ceramic: influence of cleaning methods, surface treatments, and aging.
J Dent
January 2025
DDS, MS, PhD, Department of Dentistry, Federal University of Rio Grande do Norte, Natal, Brazil. Electronic address:
Objective: To evaluate the influence of different cleaning methods, surface treatments, and aging on the repair bond strength to a CAD/CAM glass-ceramic.
Materials And Methods: Forty-eight lithium disilicate CAD/CAM ceramic blocks were fabricated, sintered, and embedded in acrylic resin. After contamination with human saliva, they were divided according to the factors "Cleaning method" (Control-water/air spray, Air-particle abrasion with AlO, Ivoclean cleaning paste), "Surface treatment" (5% Hydrofluoric acid-HF + Silane, Monobond Etch & Prime-MEP), and "Aging" (thermocycling, no thermocycling).
Influence of heat-assisted vat photopolymerization on the physical and mechanical characteristics of dental 3D printing resins.
Sci Rep
January 2025
Department of Prosthodontics, Yonsei University College of Dentistry, Yonsei-ro 50-1, Seodaemun-gu, Seoul, 03722, Republic of Korea.
The effects of heat-assisted vat photopolymerization (HVPP) on the physical and mechanical properties of 3D-printed dental resins, including the morphometric stability of 3D-printed crowns, were investigated. A resin tank was designed to maintain the resin at 30, 40, and 50 ℃ during the 3D printing process. Test specimens were fabricated using a commercial dental resin, with untreated resin serving as the control group.
View Article and Find Full Text PDFEffect of Build Orientation on Mechanical and Physical Properties of Additively Manufactured Resins Using Digital Light Processing Technology in Dentistry: A Systematic Review.
J Contemp Dent Pract
September 2024
Department of Prosthodontics, Bharati Vidyapeeth (Deemed to be University) Dental College and Hospital, Sangli, Maharashtra, India, ORCID: https://orcid.org/0000-0002-6661-0931.
Aim: The aim of this systematic review was to evaluate the effect of build orientation on the mechanical and physical properties of additively manufactured resin using digital light processing (DLP).
Background: The properties of 3D-printed materials are influenced by various factors, including the type of additive manufacturing (AM) system and build orientation. There is a scarcity of literature on the effect of build orientation on the mechanical and physical properties of additively manufactured resins using DLP technology in dentistry.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!