Purpose: The aim of this study was to evaluate the surface roughness and analyze the surface topography of five different CAD/CAM ceramics and one CAD/CAM composite resin for CEREC after milling and postmilling procedures.
Materials And Methods: Blocks of the ceramics Mark II, IPS Empress CAD, IPS e.max CAD, Suprinity and Enamic, and blocks of the composite resin Lava Ultimate were milled at CEREC MCXL. Ten flat samples of each material were obtained. The surface roughness (Ra) test was performed before and after milling, crystallization, polishing, and glaze when indicated, followed by SEM and AFM analysis. Data were submitted to one-way ANOVA with repeated measures and the Tukey HSD test (α = 0.05).
Results: The milling step significantly increased the roughness of all the tested materials (P < .05). Lithium-based ceramics (IPS e.max CAD and Suprinity) were more suitable to roughness than the other tested materials (P < .05).
Conclusions: The polishing methods were able to reduce roughness to baseline values, except for lithium-based ceramics. Glaze reduced significantly the roughness of lithium-based ceramics without a difference from the baseline. SEM and AFM images revealed that glazed surfaces are smoother than polished surfaces.
Clinical Significance: All hard-milling CAD/CAM materials, that is, fully sintered, should be only hand polished. The glaze step can be suppressed resulting in time saving. However, the glaze step in soft-milling lithium disilicate is imperative.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/jerd.12326 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Binding Kinetics of Self-Assembled Monolayers of Fluorinated Phosphate Ester on Metal Oxides for Underwater Aerophilicity.
Langmuir
January 2025
Department of Physics, Chair of Biophysics, Friedrich-Alexander-Universität Erlangen-Nürnberg, Henkestrasse 91, Erlangen 92054, Germany.
The term "aerophilic surface" is used to describe superhydrophobic surfaces in the Cassie-Baxter wetting state that can trap air underwater. To create aerophilic surfaces, it is essential to achieve a synergy between a low surface energy coating and substrate surface roughness. While a variety of techniques have been established to create surface roughness, the development of rapid, scalable, low-cost, waste-free, efficient, and substrate-geometry-independent processes for depositing low surface energy coatings remains a challenge.
View Article and Find Full Text PDFTiCT MXene Thin Films and Intercalated Species Characterized by IR-to-UV Broadband Ellipsometry.
J Phys Chem C Nanomater Interfaces
January 2025
Nanoscale Solid-Liquid Interfaces, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Schwarzschildstraße 8, 12489 Berlin, Germany.
MXenes are two-dimensional (2D) materials with versatile applications in optoelectronics, batteries, and catalysis. To unlock their full potential, it is crucial to characterize MXene interfaces and intercalated species in more detail than is currently possible with conventional optical spectroscopies. Here, we combine ultra-broadband ellipsometry and transmission spectroscopy from the mid-infrared (IR) to the deep-ultraviolet (UV) to probe quantitatively the composition, structure, transport, and optical properties of spray-coated TiCT MXene thin films with varying material properties.
View Article and Find Full Text PDFParametric optimization and sensitivity analysis of the integrated Taguchi-CRITIC-EDAS method to enhance the surface quality and tensile test behavior of 3D printed PLA and ABS parts.
Heliyon
January 2025
Department of Industrial & Production Engineering, Bangladesh University of Engineering & Technology, Dhaka, 1000, Bangladesh.
3D printing is a popular and cost-effective method for producing lightweight engineering parts with enhanced characteristics and detailed prototypes. Nevertheless, the quality of the print can be diminished by the selection of improper parameter settings. This investigation explored the impact of printing factors on the tensile behavior of polylactic acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) specimens.
View Article and Find Full Text PDFComprehensive characterization of tobacco-induced changes in enamel surface topography.
J Oral Biol Craniofac Res
December 2024
Department of Oral Biology and Oral Pathology, Saveetha Dental College and Hopsitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, Chennai, 600077, India.
Introduction: Enamel translucency, essential for the aesthetic appeal of teeth, is primarily determined by its thickness, quality, and refractive index. Several factors, including age, genetics, diet, oral hygiene practices, fluoride exposure, and acidic challenges, can influence enamel translucency. Tobacco use, in particular, leads to significant alterations in enamel appearance by penetrating its micropores, causing yellowing and browning.
View Article and Find Full Text PDFThe effects of anodization and instrumentation on titanium abutment surface characteristics and biofilm formation.
J Prosthodont
January 2025
Department of Prosthodontics, Indiana University School of Dentistry, Indianapolis, Indiana, USA.
Purpose: To assess the impact of anodization and instrumentation on titanium abutment surface characteristics (surface roughness and wettability) and biofilm formation (viability and mass).
Materials And Methods: Titanium discs were obtained from pre-milled abutment blanks made of titanium-6aluminum-7niobium alloy. Polished samples were divided into three groups: un-anodized, gold-anodized, and pink-anodized.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!