When a three-phase contact line moves along a solid surface, the contact angle no longer corresponds to the static equilibrium angle but is larger when the liquid is advancing and smaller when the liquid is receding. The difference between the advancing and receding contact angles, i.e., the contact angle hysteresis, is of paramount importance in wetting and capillarity. For example, it determines the magnitude of the external force that is required to make a drop slide on a solid surface. Until now, fundamental origin of the contact angle hysteresis has been controversial. Here, this origin is revealed and a quantitative theory is derived. The theory is corroborated by the available experimental data for a large number of solid-liquid combinations. The theory is applied in modelling the contact angle hysteresis on a textured surface, and these results are also in quantitative agreement with the experimental data.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1063/1.4996912 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Development of an antimicrobial tissue conditioner with quaternary ammonium methacryloxy silane (K18): An in vitro study.
J Prosthodont Res
January 2025
Department of Comprehensive Dentistry, UT Health San Antonio, San Antonio, USA.
Purpose: To determine the effects of K18 quaternary ammonium methacryloxy silane (QAS) on tissue conditioner materials and their antimicrobial properties.
Methods: 30% K18 QAS in methyl methacrylate (MMA; K18-MMA; 0%, 15%, and 20% w/w) was incorporated into a commercial tissue conditioner (Coe comfort). The degree of curing (Shore A hardness), hydrophilicity (contact angle), flow, liquid sorption, mass loss, and antimicrobial properties of Streptococcus mutans, Streptococcus sanguinis, and Candida albicans were determined.
Highly sensitive, breathable, and superhydrophobic dome structure nonwoven-based flexible pressure sensor utilizing machine learning for handwriting recognition.
Int J Biol Macromol
January 2025
Shaoxing Key Laboratory of High Performance Fibers & Products, Shaoxing University, Shaoxing, Zhejiang 312000, China; Shaoxing Sub-center of National Engineering Research Center for Fiber-based Composites, Shaoxing University, Zhejiang, Shaoxing 312000, China; Key Laboratory of Clean Dyeing and Finishing Technology of Zhejiang Province, Shaoxing, Zhejiang 312000, China. Electronic address:
Wearable devices that incorporate flexible pressure sensors have shown great potential for human-machine interaction, speech recognition, health monitoring, and handwriting recognition.However, achieving high sensitivity, durability, wide detection range, and breathability through cost-effective fabrication remains challenging. Through ultrasound-assisted modification and impregnation-drying, dome-structured nonwovens/rGO/PDMS flexible pressure sensors were developed.
View Article and Find Full Text PDFA three-dimensional kinematic analysis of bipedal walking in a white-handed gibbon (Hylobates lar) on a horizontal pole and flat surface.
Primates
January 2025
Laboratory of Biological Anthropology, Graduate School of Human Sciences, Osaka University, Suita, Osaka, Japan.
Gibbons, a type of lesser ape, are brachiators but also walk bipedally and without forelimb assistance, not only on the ground but also on tree branches. The arboreal bipedal walking strategy of the gibbons has been studied in previous studies in relation to two-dimensional (2D) kinematic analysis. However, because tree branches and the ground differ greatly in width, leading to a constrained foot contact point on the tree branches, gibbons must adjust their 3D joint motions of trunk and hindlimb on the tree branches.
View Article and Find Full Text PDFThe effects of anodization and instrumentation on titanium abutment surface characteristics and biofilm formation.
J Prosthodont
January 2025
Department of Prosthodontics, Indiana University School of Dentistry, Indianapolis, Indiana, USA.
Purpose: To assess the impact of anodization and instrumentation on titanium abutment surface characteristics (surface roughness and wettability) and biofilm formation (viability and mass).
Materials And Methods: Titanium discs were obtained from pre-milled abutment blanks made of titanium-6aluminum-7niobium alloy. Polished samples were divided into three groups: un-anodized, gold-anodized, and pink-anodized.
Towards cell-adhesive, 4D printable PCL networks through dynamic covalent chemistry.
J Mater Chem B
January 2025
Department of Textile and Fibre Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi-110016, India.
In recent years, the development of biodegradable, cell-adhesive polymeric implants and minimally invasive surgery has significantly advanced healthcare. These materials exhibit multifunctional properties like self-healing, shape-memory, and cell adhesion, which can be achieved through novel chemical approaches. Engineering of such materials and their scalability using a classical polymer network without complex chemical synthesis and modification has been a great challenge, which potentially can be resolved using biobased dynamic covalent chemistry (DCC).
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!