Coating individual bacterial cells with conjugated polymers to endow them with more functionalities is highly desirable. Here, we developed an in situ polymerization method to coat polypyrrole on the surface of individual Shewanella oneidensis MR-1, Escherichia coli, Ochrobacterium anthropic or Streptococcus thermophilus. All of these as-coated cells from different bacterial species displayed enhanced conductivities without affecting viability, suggesting the generality of our coating method. Because of their excellent conductivity, we employed polypyrrole-coated Shewanella oneidensis MR-1 as an anode in microbial fuel cells (MFCs) and found that not only direct contact-based extracellular electron transfer is dramatically enhanced, but also the viability of bacterial cells in MFCs is improved. Our results indicate that coating individual bacteria with conjugated polymers could be a promising strategy to enhance their performance or enrich them with more functionalities.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1002/anie.201704729 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effect of post-processing on the surface, optical, mechanical, and dimensional properties of 3D-printed orthodontic clear retainers.
Clin Oral Investig
January 2025
School of Materials Science and Innovation, Faculty of Science, Mahidol University, Phuttamonthon 4 Road, Salaya, Phuttamonthon District, Nakhon Pathom, 73170, Thailand.
Objectives: To address the high surface roughness and poor optical properties of three-dimensional (3D) printed orthodontic clear retainers, an alternative post-processing protocol was investigated with the goal of achieving improved surface, optical, and mechanical properties while preserving dimensional accuracy.
Materials And Methods: Samples were prepared from two biocompatible methacrylate-based 3D-printing resins (Formlabs Dental LT Clear V2, NextDent OrthoFlex) and one thermoplastic material (Duran). For the 3D-printed resins, one group was post-processed by rinsing in isopropyl alcohol, while another group was centrifuged before post-curing in glycerine.
Adhesion properties of polyimide coated stacks: An in-depth analysis of the cross-sectional nanoindentation method.
Heliyon
December 2024
Institute of Chemical Technologies and Analytics CTA, TU Wien, Getreidemarkt 9/164, 1060, Vienna, Austria.
Adhesion at the interface between dissimilar materials in the semiconductor industry is an important topic, but reliable quantitative methods for strongly adhesive or highly plastic layers are hardly available. This study aims to investigate the suitability of the cross-sectional nanoindentation (CSN) method for determination of the critical energy release rate of thin film stacks in the presence of a polyimide layer as a representative structure for such a case. For this purpose, the adhesion of a deliberately weakened Si/SiO interface in a Si/SiO/Al/SiN/polyimide stack is examined by systematic variation of the experimental parameters.
View Article and Find Full Text PDFA rare case of extrapulmonary hamartoma on the visceral pleura treated by uniportal VATS: case report and literature review.
J Cardiothorac Surg
January 2025
Department of Thoracic Surgery, Ningbo No.2 Hospital, 41 Xibei Road, Ningbo, 315010, P. R. China.
Pulmonary hamartomas are common. However, extrapulmonary hamartomas on the Visceral Pleura are very rare. We treated a patient with a pulmonary nodule at the left lower lobe by uniportal video-assisted thoracoscopic wedge resection, which showed a yellow nodule located on the visceral pleura.
View Article and Find Full Text PDFEnhancing visible light degradation of gaseous formaldehyde with CuO/OVs-TiO photocatalyst loaded wallpaper: Preparation, efficacy and mechanism.
Chemosphere
January 2025
Beijing Key Laboratory for Source Control Technology of Water Pollution, Engineering Research Center for Water Pollution Source Control and Eco-remediation, Beijing Forestry University, Beijing, 100083, China. Electronic address:
Photocatalytic oxidation is considered to be a highly promising technology for indoor formaldehyde (HCHO) abatement. However, powdered photocatalysts encounter practical challenges due to their recycling difficulties and propensity for aggregation. In this study, we developed a CuO/OVs-TiO photocatalyst dispersion using various physical and chemical methods, which could be stabilized for an extended period.
View Article and Find Full Text PDFSmartphone-based mobile digital pressure sensor for quantitative point-of-care testing of respiratory syncytial virus infection.
Talanta
January 2025
Department of Transfusion Medicine, School of Laboratory Medicine and Biotechnology, Southern Medical University, Guangzhou, 510515, China; Shenzhen Bao'an District Central Blood Station, Shenzhen, 518101, China. Electronic address:
Respiratory syncytial virus (RSV) is a major cause of acute respiratory tract infections in infants and elderly individuals, leading to hospitalisation and potentially fatal outcomes, posing a serious threat to global health and economy. This study proposes a smartphone-based mobile digital pressure sensor (smartphone-MDPS) for the quantitative detection of the RSV fusion protein (RSV-F) in clinical nasopharyngeal samples. The smartphone-MDPS utilized two monoclonal antibodies (mAbs) specific to the F protein, of which mAb1 was conjugated with Au@PtNPs (Au@PtNPs-mAb1) as the detection antibody and mAb2 was coupled with magnetic beads (MB-mAb2) as a coating antibody to establish a novel sandwich immunoassay.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!