In this paper, an attempt is made to apply the African Buffalo Optimization (ABO) to tune the parameters of a PID controller for an effective Automatic Voltage Regulator (AVR). Existing metaheuristic tuning methods have been proven to be quite successful but there were observable areas that need improvements especially in terms of the system's gain overshoot and steady steady state errors. Using the ABO algorithm where each buffalo location in the herd is a candidate solution to the Proportional-Integral-Derivative parameters was very helpful in addressing these two areas of concern. The encouraging results obtained from the simulation of the PID Controller parameters-tuning using the ABO when compared with the performance of Genetic Algorithm PID (GA-PID), Particle-Swarm Optimization PID (PSO-PID), Ant Colony Optimization PID (ACO-PID), PID, Bacteria-Foraging Optimization PID (BFO-PID) etc makes ABO-PID a good addition to solving PID Controller tuning problems using metaheuristics.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC5404770 | PMC |
http://journals.plos.org/plosone/article?id=10.1371/journal.pone.0175901 | PLOS |
J R Soc Interface
January 2025
SSM- School for Advanced Studies Via Mezzocannone 4, Naples 80138, Italy.
This article presents the first implementation of a proportional-integral-derivative (PID) biomolecular controller within a consortium of different cell populations, aimed at robust regulation of biological processes. By leveraging the modularity and cooperative dynamics of multiple engineered cell populations, we develop a comprehensive analysis of the performance and robustness of P, PD, PI and PID control architectures. Our theoretical findings, validated through experiments using the BSim agent-based simulation platform for bacterial populations, demonstrate the robustness and effectiveness of our multicellular PID control strategy.
View Article and Find Full Text PDFISA Trans
January 2025
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, Jiangsu 210094, PR China. Electronic address:
Hysteresis characteristics widely affects the performance and reliability of pneumatic systems across various industrial applications. Addressing this challenge can significantly enhance system efficiency and precision. This paper aims to develop a rapid and accurate method for controlling the actuating force of a Single-Acting Pneumatic Cylinder (SAPC), considering hysteresis characteristic.
View Article and Find Full Text PDFClin Neurophysiol
January 2025
Department of Neurosurgery, The University of Iowa, Iowa City, IA 52242, USA; Iowa Neuroscience Institute, The University of Iowa, Iowa City, IA 52242, USA.
Objectives: (1) Gain insight into the mechanisms of postoperative delirium (POD). (2) Determine mechanistic overlap with post-ictal delirium (PID). Epilepsy patients undergoing intracranial electrophysiological monitoring can experience both POD and PID, and thus are suitable subjects for these investigations.
View Article and Find Full Text PDFSensors (Basel)
January 2025
Faculty of Minas Gerais (FAMINAS), Muriaé 36888-233, Brazil.
This paper focuses on the modeling, control, and simulation of an over-actuated hexacopter tilt-rotor (HTR). This configuration implies that two of the six actuators are independently tilted using servomotors, which provide high maneuverability and reliability. This approach is predicted to maintain zero pitch throughout the trajectory and is expected to improve the aircraft's steering accuracy.
View Article and Find Full Text PDFMicromachines (Basel)
December 2024
Lightweight Optics and Advanced Materials Technology Center, Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu 610209, China.
Direct energy deposition is an additive technology that can quickly manufacture irregularly shaped quartz-glass devices. Based on this technology and coaxial laser/wire feeding, open-loop tests were conducted under different process parameters. A closed-loop temperature control system was designed and built for the molten pool temperature in quartz-glass additive manufacturing.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!