Present work investigates the recycling of waste printed circuit boards (PCBs) by cracking of its multi-layered structure by using dimethylacetamide (DMA). The study shows that cracking and separation of layers of PCBs increases as the temperature increases; and decreases as the surface area of PCBs increases. After separation of layers, the used solvent was analyzed by proton and carbon nuclear magnetic resonance spectroscopy (NMR) to understand the dissolution phenomenon of resin. Further, NMR and Fourier transform infrared spectroscopy analysis of DMA sample after 1h, 2h, 3h, 4h and 8h of reaction with PCBs at 433K and PCB:DMA ratio (wt/vol) of 3:10 has been carried out to investigate the mechanism of dissolution of resin. These studies revealed that hydroxyl group of PCBs polymeric chain participates in hydrogen bonding with parent carbonyl group of DMA molecule that results in the solvation of resin. Possible chemical reaction based on the above finding has been discussed. Using this technique, separation of the metallic fraction without application of any energy intensive mechanical pre-processing is possible.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.wasman.2017.04.013 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Sustainable Multi-Cycle Physical Recycling of Expanded Polystyrene Waste for Direct Ink Write 3D Printing and Casting: Analysis of Mechanical Properties.
Polymers (Basel)
December 2024
Department of Applied Mathematics, Materials Science and Engineering and Electronic Technology, Universidad Rey Juan Carlos, Calle Tulipán s/n, 28933 Móstoles, Spain.
This work investigates the sustainable reuse of expanded polystyrene (EPS) waste through a multi-cycle physical recycling process involving dissolution in acetone and subsequent manufacturing via Direct Ink Write (DIW) 3D printing and casting. Morphology and mechanical properties were evaluated as a function of the manufacturing technique and number of dissolution cycles. Morphological analysis revealed that casted specimens better replicated the target geometry, while voids in 3D-printed specimens aligned with the printing direction due to rapid solvent evaporation.
View Article and Find Full Text PDFMechanical Property Characterization of Virgin and Recycled PLA Blends in Single-Screw Filament Extrusion for 3D Printing.
Polymers (Basel)
December 2024
Department of Mechanical & Industrial Engineering, Rochester Institute of Technology, Dubai 341055, United Arab Emirates.
Additive manufacturing is an attractive technology due to its versatility in producing parts with diverse properties from a single material. However, the process often generates plastic waste, particularly from failed prints, making sustainability a growing concern. Recycling this waste material presents a potential solution for reducing environmental impact while creating new, functional parts.
View Article and Find Full Text PDFTowards Green Dentistry: Evaluating the Potential of 4D Printing for Sustainable Orthodontic Aligners with a Reduced Carbon Footprint.
Polymers (Basel)
December 2024
Institute for Microelectronics and Microsystems, National Research Council, Via del Fosso del Cavaliere, 100, 00133 Rome, Italy.
Clear aligners have transformed orthodontic care by providing an aesthetic, removable alternative to traditional braces. However, their significant environmental footprint, contributing to approximately 15,000 tons of plastic waste annually, poses a critical challenge. To address this issue, advancements in 4D printing have introduced "smart" aligners with shape memory properties, enabling reshaping and reducing the number of aligners required per treatment.
View Article and Find Full Text PDFThe Effect of Elastomer Content and Annealing on the Physical Properties of Upcycled Polyethylene Terephthalate-Maleated Styrene Ethylene Butylene Styrene Blends for Additive Manufacturing.
Materials (Basel)
December 2024
Polymer Extrusion Lab, The University of Texas at El Paso, El Paso, TX 79968, USA.
In the work presented here, we explore the upcycling of polyethylene terephthalate (PET) that was derived from water bottles. The material was granulated and extruded into a filament compatible with fused filament fabrication (FFF) additive manufacturing platforms. Three iterations of PET combined with a thermoplastic elastomer, styrene ethylene butylene styrene with a maleic anhydride graft (SEBS-g-MA), were made with 5, 10, and 20% by mass elastomer content.
View Article and Find Full Text PDFBiocomposites Based on Mould Biomass and Waste Fibres for the Production of Agrotextiles: Technology Development, Material Characterization, and Agricultural Application.
Materials (Basel)
December 2024
Biotechnika Poland Sp. z o.o., Tymienieckiego 25, 90-350 Łódź, Poland.
This study explores the potential use of mould biomass and waste fibres for the production of agrotextiles. First, 20 mould strains were screened for efficient mycelium growth, with optimized conditions of temperature, sources of carbon and nitrogen in the medium, and type of culture (submerged or surface). A method was developed for creating a biocomposite based on the mould mycelium, reinforced with commercial bleached softwood kraft (BSK) pulp and fibre additives (cotton, hemp).
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!