We present an improved heater design for thermionic cathodes using a rhenium filament encased in a boron nitride ceramic sleeve. This heater is relatively simple to fabricate, yet has been successfully used to reliably and repeatably light a lanthanum hexaboride (LaB6) hollow cathode based on a previously published design without noticeable filament degradation over hundreds of hours of operation. The high decomposition temperature of boron nitride (2800 C for inert environments) and melting point for rhenium (3180 C) make this heater especially attractive for use with LaB6, which may require operating temperatures upwards of 1700 C. While boron nitride decomposes in air above 1000 C, the heater was used only at vacuum with an inert gas discharge, and no degradation was observed. Limitations of current state of the art cathode heaters are also discussed and compared with the rhenium-boron nitride combination.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1063/1.4976728 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Self-Foldable Three-Dimensional Biointerfaces by Strain Engineering of Two-Dimensional Layered Materials on Polymers.
ACS Appl Mater Interfaces
January 2025
School of Computation, Information and Technology, Technical University of Munich, Garching 85748, Germany.
Two-dimensional layered materials (2DLMs) have received increasing attention for their potential in bioelectronics due to their favorable electrical, optical, and mechanical properties. The transformation of the planar structures of 2DLMs into complex 3D shapes is a key strategic step toward creating conformal biointerfaces with cells and applying them as scaffolds to simultaneously guide their growth to tissues and enable integrated bioelectronic monitoring. Using a strain-engineered self-foldable bilayer, we demonstrate the facile formation of predetermined 3D microstructures of 2DLMs with controllable curvatures, called microrolls.
View Article and Find Full Text PDFMolecular dynamics simulations of functionalized hBN nanopores in water: Ab initio force field and implications for water desalination.
J Chem Phys
January 2025
Department of Chemical Engineering, Indian Institute of Science, Bengaluru, Karnataka 560012, India.
Heteropolar two-dimensional materials, including hexagonal boron nitride (hBN), are promising candidates for seawater desalination and osmotic power harvesting, but previous simulation studies have considered bare, unterminated nanopores in molecular dynamics (MD) simulations. There is presently a lack of force fields to describe functionalized nanoporous hBN in aqueous media. To address this gap, we conduct density functional theory (DFT)-based ab initio MD simulations of hBN nanopores surrounded by water molecules.
View Article and Find Full Text PDFChallenges in Synthesizing Hexagonal Boron Nitride "Quantum" Dots.
Nano Lett
January 2025
School of Physics, Xidian University, No. 2 Taibai South Road, Xi'an 710071, China.
Fluorescent nanodots derived from hexagonal boron nitride (-BN) have garnered significant attention over the past decade. As a result, various synthesis methods─encompassing both bottom-up hydrothermal reactions and top-down exfoliation processes─have been deemed "successful" in producing BN nanodots. Nevertheless, this Perspective emphasizes that substantial challenges remain in the synthesis of "true" nanodots composed mainly of -BN units, as many so-called successful syntheses reported in the literature involve some mischaracterizations.
View Article and Find Full Text PDFSilicone Composites with Electrically Oriented Boron Nitride Platelets and Carbon Microfibers for Thermal Management of Electronics.
Polymers (Basel)
January 2025
Faculty of Mechanics, University Politehnica of Timisoara, Piata Victoriei 2, 300006 Timisoara, Romania.
This study investigated silicone composites with distributed boron nitride platelets and carbon microfibers that are oriented electrically. The process involved homogenizing and dispersing nano/microparticles in the liquid polymer, aligning the particles with DC and AC electric fields, and curing the composite with IR radiation to trap particles within chains. This innovative concept utilized two fields to align particles, improving the even distribution of carbon microfibers among BN in the chains.
View Article and Find Full Text PDFFrom Powders to Performance-A Comprehensive Study of Two Advanced Cutting Tool Materials Sintered with Pressure Assisted Methods.
Materials (Basel)
January 2025
Faculty of Materials Science and Ceramics, AGH University of Krakow, 30-059 Krakow, Poland.
Article Synopsis
- The paper examines two tool materials for machining Inconel 718, made using different sintering methods: High Pressure-High Temperature (HPHT) and Spark Plasma Sintering (SPS).
- One material, BNT, is predominantly cubic boron nitride and showed significant changes in phase composition post-sintering; the other, AZW, maintained a similar composition throughout.
- Both composites demonstrated high mechanical properties, with BNT displaying a higher Young's modulus and hardness than AZW, and both were effective in machining but differed in performance and cost.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!