Introduction: The dual-mobility cup (DMC) was introduced in 1979. Due to lack of referenced publications, this interesting and innovating concept was ignored during close to 20 years. However, 180 studies (level III or IV) have now been published. Evidence-based medicine is based on level I studies. Over the past three decades, the role of national registries developed with the intention of surveying orthopaedic implants. In 2012, we developed, registered, and implemented a specific database for contemporary DMC.
Material And Methods: Data are collected with an electronic case-report form, and this evaluation is limited to a single product line . From May 2012 to December 2016, 2090 cases of Quattro cup implantation have been registered; results of the first 636 primary cases with a minimum follow-up of three years were previously reported (series 1). Of the 1454 remaining cases, dislocation rate only was monitored (series 2) and results are reported here.
Results: In series1 comprising 553 degenerative diseases and 83 proximal femoral fractures (PFF), one dislocation (1.2%) occurred in PFF and none in degenerative disease. Survivorship (infection excluded) at three years was 99.8%. In series 2 (1315 degenerative diseases; 139 PFFs), dislocation rate was 0.27% (four cases). In neither series did we observe any intraprosthetic dislocation.
Discussion: Results of this private regional register confirm the high efficiency of DMC to decrease dislocation rate (0.23%). Few outcomes of DMC in primary total hip arthroplasty (THA) are published in national registries. The Swedish Hip Arthroplasty Register has reported on 287 primary DMC hips of 78,098 THAs. No dislocations were reported. We conclude that DMC decreases dislocation rate, and the national registry of Lithuania also reports a significant decrease in the rate of revision for dislocation in the DMC group. These data-available online-allow us to monitor DMC in real time, although they lack short-term follow-up.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s00264-017-3405-6 | DOI Listing |
Insights Imaging
January 2025
Department of Radiology, Radiation Oncology and Medical Physics Faculty of Medicine, University of Ottawa, Ottawa, ON, Canada.
Objective: To determine the feasibility, yield, and safety of fluoroscopic-guided aspiration of the acutely dislocated total hip arthroplasty (AD-THA).
Materials And Methods: IRB-approved, retrospective review of fluoroscopic-guided aspirations of AD-THA (January 2005-December 2023) was performed. Data from electronic charts and fluoroscopy images/reports were obtained.
Nanomaterials (Basel)
December 2024
Analytical and Testing Center, Northeastern University, Shenyang 110819, China.
High-performance lightweight materials are urgently needed because of energy savings and emission reduction. Here, we design a new steel with a low density of 6.41 g/cm, which is a 20% weight reduction compared to the conventional steel.
View Article and Find Full Text PDFScand J Surg
January 2025
Interdisciplinary Endoscopy Centre, Heidelberg University Hospital, Im Neuenheimer Feld 410, 69120 Heidelberg, Germany.
Background And Aims: The therapeutic management of fistulas presents significant challenges, often involving both conservative and surgical approaches. Despite these interventions, recurrence and postoperative mortality rates remain high. Endoscopic stent insertion into the fistula, along with the creation of a stent stoma, may offer a promising alternative for patients who fail surgical or conservative therapies.
View Article and Find Full Text PDFBMC Musculoskelet Disord
January 2025
Department of Orthopedic Surgery, Chang Gung Memorial Hospital, Linkou, Taiwan.
Purpose: The Coronavirus Disease 2019 (COVID-19) pandemic delayed elective procedures such as total joint arthroplasty. As surgical volumes return to prepandemic levels, understanding the implications of COVID-19 becomes imperative. This study explored the effects of COVID-19 on the short-term outcomes of hip arthroplasty.
View Article and Find Full Text PDFSci Technol Adv Mater
December 2024
Research Center for Structural Materials, National Institute for Materials Science (NIMS), Tsukuba, Japan.
Hydrogen-assisted (HA) fatigue crack growth (FCG) occurs in ferritic steels, wherein H-dislocation interaction plays a vital role. We aim to model the HAFCG mechanism based on the within the crack tip zone. Our modeling framework is as follows: H is condensed into crack tip and trapped by dislocations; these H significantly decrease dislocation mobility; stress relief via crack blunting is suppressed; localized brittle fracture triggers HAFCG.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!