Background: Epidemiological studies have indicated an increasing incidence of radiation induced secondary cancer (SC) in breast cancer patients after radiotherapy (RT), most commonly in the contra-lateral breast (CLB). The present study was conducted to estimate the SC risk in the CLB following 3D conformal radiotherapy techniques (3DCRT) including wedge field and forward intensity modulated radiotherapy (fIMRT) based on the organ equivalent dose (OED). Material and Methods: RT plans treating the chest wall with conformal wedge field and fIMRT plans were created for 30 breast cancer patients. The risks of radiation induced cancer were estimated for the CLB using dose-response models: a linear model, a linear-plateau model and a bell-shaped model with full dose response accounting for fractionated RT on the basis of OED. Results: The plans were found to be ranked quite differently according to the choice of model; calculations based on a linear dose response model fIMRT predict statistically significant lower risk compared to the enhanced dynamic wedge (EDW) technique (p-0.0089) and a non-significant difference between fIMRT and physical wedge (PW) techniques (p-0.054). The widely used plateau dose response model based estimation showed significantly lower SC risk associated with fIMRT technique compared to both wedge field techniques (fIMRT vs EDW p-0.013, fIMRT vs PW p-0.04). The full dose response model showed a non-significant difference between all three techniques in the view of second CLB cancer. Finally the bell shaped model predicted interestingly that PW is associated with significantly higher risk compared to both fIMRT and EDW techniques (fIMRT vs PW p-0.0003, EDW vs PW p-0.0032). Conclusion: In conclusion, the SC risk estimations of the CLB revealed that there is a clear relation between risk associated with wedge field and fIMRT technique depending on the choice of model selected for risk comparison.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC5454644PMC
http://dx.doi.org/10.22034/APJCP.2016.17.12.5107DOI Listing

Publication Analysis

Top Keywords

wedge field
20
breast cancer
16
dose response
16
radiation induced
12
cancer patients
12
response model
12
fimrt
10
model
9
chest wall
8
conformal wedge
8

Similar Publications

The Conference 2024 provides a platform to promote the development of an innovative scientific research ecosystem for microbiome and One Health. The four key components - Technology, Research (Biology), Academic journals, and Social media - form a synergistic ecosystem. Advanced technologies drive biological research, which generates novel insights that are disseminated through academic journals.

View Article and Find Full Text PDF

Patient Insights on Integrating Sleep Apnea Testing into Routine Stroke and TIA Care.

J Patient Exp

December 2024

Pain Research, Informatics, and Multi-morbidities, and Education (PRIME) Center, VA Connecticut Healthcare System, West Haven, CT, USA.

AHA/ASA guidelines recommend patients with ischemic stroke or transient ischemic attack (TIA) be considered for obstructive sleep apnea (OSA) evaluation, given the high prevalence of OSA and improved outcomes for cerebrovascular disease when OSA is treated. However, OSA testing has not been incorporated into routine cerebrovascular management. We interviewed 30 patients hospitalized for acute stroke/TIA at six Veterans Affairs facilities participating in a stepped-wedge implementation trial to improve timely OSA testing after stroke/TIA.

View Article and Find Full Text PDF

The deflector jet pressure servo valve (DJPSV), a critical component of the aircraft brake servo system, requires a precise foundational model for performance analysis, optimization, and enhancement. However, the complexity of the jet process within the V-groove of the deflector plate presents challenges for accurate mathematical modeling. To address this issue, the paper takes the DJPSV as the research object, carries out detailed mathematical modeling of its components, analyzes the influencing factors of the performance of the key component-the front stage-and optimizes the design of the key factors.

View Article and Find Full Text PDF

Tip-Induced 3D Printing on the Nanoscale with Field Emission Scanning Probes.

Small

December 2024

Institute of Micro- and Nanotechnologies MacroNano, Microsystems Technology Group, Technische Universität Ilmenau, Max-Planck-Ring 12, 98693, Ilmenau, Germany.

3D printing down to the nanoscale remains a significant challenge. In this paper, the study explores the use of scanning probes that emit low-energy electrons (<100 eV) coupled with the localized injection and electron-induced decomposition of precursor molecules, for the precise localized deposition of 3D nanostructures. The experiments are performed inside the chamber of a scanning electron microscope (SEM), enabling the use of the in-built gas injector system (GIS) with gaseous naphthalene precursor for carbon deposition, as well as immediate inspection of the deposits by SEM.

View Article and Find Full Text PDF

Background: Different dose calculation methods vary in accuracy and speed. While most methods sacrifice precision for efficiency Monte Carlo (MC) simulation offers high accuracy but slower calculation. ISOgray treatment planning system (TPS) uses Clarkson, collapsed cone convolution (CCC), and fast Fourier transform (FFT) algorithms for dose distribution.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!