The Letter describes a hybrid multiplexing scheme for a multi-longitudinal-mode fiber laser sensor array by combining wavelength-division multiplexing and frequency-division multiplexing techniques. The proposed multiplexing system consists of many subgroups, each of which has many fiber laser sensors with approximately equal laser-operating wavelengths but different cavity lengths. Each sensor in one subgroup can be interrogated by using frequency-division multiplexing technology because of different sensors with different beat frequencies. For different subgroups, they are characteristic of different laser-operating wavelengths. Each subgroup can be divided into the designed channel by dense wavelength-division multiplexers. At last, a 4×4 sensor multiplexing system was experimentally validated. The strain or temperature applied on each sensor was successfully extracted. The proposed multiplexing system provides a dramatic increase in the number of multiplexed sensors. It greatly reduces the weight, volume, and cost of each sensor and offers a competitive solution for a large-scale monitoring system.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/OL.42.000159 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
High-Performance Optical Fiber Displacement Sensor with Extended Linear Range and Sensitivity.
Sensors (Basel)
January 2025
Department of Communications Engineering, University of the Basque Country, 48013 Bilbao, Spain.
Optical Fiber Displacement Sensors (OFDSs) provide several advantages over conventional sensors, including their compact size, flexibility, and immunity to electromagnetic interference. These features make OFDSs ideal for use in confined spaces, such as turbines, where direct laser access is impossible. A critical aspect of OFDS performance is the geometry of the fiber bundle, which influences key parameters such as sensitivity, range, and dead zones.
View Article and Find Full Text PDFRadiation-Induced Wavelength Shifts in Fiber Bragg Gratings Exposed to Gamma Rays and Neutrons in a Nuclear Reactor.
Sensors (Basel)
January 2025
Soreq NRC, Yavne 81800, Israel.
Fiber Bragg gratings (FBGs) inscribed by UV light and different femtosecond laser techniques (phase mask, point-by-point, and plane-by-plane) were exposed-in several irradiation cycles-to accumulated high doses of gamma rays (up to 124 MGy) and neutron fluence (8.7 × 10/cm) in a research-grade nuclear reactor. The FBG peak wavelengths were measured continuously in order to monitor radiation-induced shifts.
View Article and Find Full Text PDFEffect of Laser Selective Melting on the Microstructure and Properties of Martensitic Stainless Steel After Annealing Treatment.
Materials (Basel)
January 2025
3D Printing Research and Engineering Technology Center, Beijing Institute of Aeronautical Materials, Beijing 100095, China.
This work investigated the CrNiMo stainless steel using laser selective melting (SLM) technology and explored the effect of the tempering temperature on the microstructure and properties. After the tempering treatment, the quenched martensite transformed from a metastable to steady state, and residual austenite was formed. The results indicated that the elongation of the transverse specimen showed an upward trend as the tempering temperature increased, while the elongation of the longitudinal specimen first increased and then decreased.
View Article and Find Full Text PDFA Precessing-Coin-like Rotary Actuator for Distal Endoscope Scanners: Proof-of-Concept Study.
Micromachines (Basel)
January 2025
Department of Electrical and Computer Engineering, University of British Columbia, Vancouver, BC V6T 1Z4, Canada.
This paper presents, for the first time, a rotary actuator functionalized by an inclined disc rotor that serves as a distal optical scanner for endoscopic probes, enabling side-viewing endoscopy in luminal organs using different imaging/analytic modalities such as optical coherence tomography and Raman spectroscopy. This scanner uses a magnetic rotor designed to have a mirror surface on its backside, being electromagnetically driven to roll around the cone-shaped hollow base to create a motion just like a precessing coin. An optical probing beam directed from the probe's optic fiber is passed through the hollow cone to be incident and bent on the back mirror of the rotating inclined rotor, circulating the probing beam around the scanner for full 360° sideway imaging.
View Article and Find Full Text PDFResearch on Envelope Profile of Lithium Niobate on Insulator Stepped-Mode Spot Size Converter.
Micromachines (Basel)
January 2025
School of Physics and Optoelectronic Engineering, Institute of Laser Engineering, Beijing University of Technology, Beijing 100124, China.
To enhance the end-face coupling efficiency of lithium niobate on insulator (LNOI) chips, in conjunction with current device fabrication processes, a stepped spot size converter (SSC) based on a special outer envelope profile has been proposed and investigated. This stepped SSC can reduce the coupling loss between the LNOI waveguide and a normal single-mode optical fiber. First, the output waveguide of a mode converter was proposed and simulated, in which the mode field had the biggest overlapping integral factor with a single-mode fiber (MDF ≈ 9.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!