We study the formation of yield-stress fluid foams in millifluidic flow-focusing and T-junction devices. First, we provide a phase diagram for the unsteady operating regimes of bubble production when the gas pressure and the yield-stress fluid flow rate are imposed. Three regimes are identified: a co-flow of gas and yield-stress fluid, a transient production of bubble and a flow of yield-stress fluid only. Taking wall slip into account, we provide a model for the pressure at the onset of bubble formation. Then, we detail and compare two simple methods to ensure steady bubble production: regulation of the gas pressure or flow-rate. These techniques, which are easy to implement, thus open pathways for controlled production of dry yield-stress fluid foams as shown at the end of this article.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1039/c6sm02054b | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
The development of thickened fermented rice milk formulation for people with dysphagia: A view of multiple in vitro simulation methods.
Food Res Int
February 2025
College of Food Science, Chongqing Key Laboratory of Speciality Food Co-Built by Sichuan and Chongqing, Southwest University, Chongqing 400715 China. Electronic address:
Based on the huge blank of thickened fluid staple food for people with dysphagia, multiple in vitro simulations were utilized to develop the thickened fermented rice milk. Here, the effect of amylase content, hydrolysis time and thickener content were considered. The rheological study and Cambridge throat evaluation revealed that hydrolysis could significantly reduce the viscosity and yield stress of fermented rice milk, accompanied by the decreased swallowing residue.
View Article and Find Full Text PDFInfluence of CO Treatment Pressure on the Chemical Composition and Rheological Properties of Degassed Waxy Crude Oil.
ACS Omega
December 2024
College of Pipeline and Civil Engineering, China University of Petroleum (East China), Qingdao, Shandong 266580, People's Republic of China.
Article Synopsis
- The study investigates how enhanced oil recovery using carbon dioxide (CO) alters the properties of crude oil, specifically focusing on wax characteristics and viscosity changes.
- As the treatment pressure increases from atmospheric levels to higher pressures (up to 25 MPa), notable changes in the composition of crude oil occur, including decreases in light hydrocarbons and increases in paraffins and wax.
- Treatment with supercritical CO (scCO) leads to smaller wax crystal sizes and increased viscosity, with significant enhancements in gelation characteristics and wax precipitation temperatures, especially notable between pressures of 5 to 15 MPa.
Rheology of dilute and semi-dilute non-Brownian suspensions made of irregular porous particles in a Newtonian fluid.
J Colloid Interface Sci
December 2024
Dept. of Engineering, University of Campania Luigi Vanvitelli, Real Casa dell'Annunziata, via Roma 29, 81031 Aversa, CE, Italy. Electronic address:
Hypothesis: The porosity affects the rheological response of porous particle suspensions.
Experiments: Non-Brownian suspensions of porous particles immersed in a Newtonian Polyisobutene are investigated. Three different particles, with different porosity, pore structure and similar size, and non-porous irregular particles are used.
Impact of organic contaminant viscosity and cation hydrated radius on the rheological properties of sodium-bentonite: experimental and numerical investigations.
Environ Monit Assess
December 2024
Department of Civil, Environmental, and Ocean Engineering, Stevens Institute of Technology, Hoboken, NJ, USA.
Soil contamination by organic and hazardous substances is a critical environmental issue, particularly in developing countries. This study investigates the limitations of double-layer theory for bentonite-organic contaminant interactions through experimental and numerical analysis. Using NaCl and KCl as salts and acetone, isopropyl alcohol, and glycerol as organic contaminants, the research explores the rheological properties of Na-bentonite dispersions.
View Article and Find Full Text PDFEmbedded 3D Printing for Microchannel Fabrication in Epoxy-Based Microfluidic Devices.
Polymers (Basel)
November 2024
State Key Laboratory of High-Performance Precision Manufacturing, School of Mechanical Engineering, Dalian University of Technology, Dalian 116024, China.
Microfluidic devices offer promising solutions for automating various biological and chemical procedures. Epoxy resin, known for its excellent mechanical properties, chemical resistance, and thermal stability, is widely used in high-performance microfluidic devices. However, the poor printability of epoxy has limited its application in 3D printing technologies for fabricating epoxy-based microfluidic devices.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!