Ionization of atoms and molecules in strong laser fields is a fundamental process in many fields of research, especially in the emerging field of attosecond science. So far, demonstrably accurate data have only been acquired for atomic hydrogen (H), a species that is accessible to few investigators. Here, we present measurements of the ionization yield for argon, krypton, and xenon with percent-level accuracy, calibrated using H, in a laser regime widely used in attosecond science. We derive a transferable calibration standard for laser peak intensity, accurate to 1.3%, that is based on a simple reference curve. In addition, our measurements provide a much needed benchmark for testing models of ionization in noble-gas atoms, such as the widely employed single-active electron approximation.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1103/PhysRevLett.117.053001 | DOI Listing |
Sensors (Basel)
December 2024
Department of Systems Design Engineering, University of Waterloo, Waterloo, ON N2L 3G1, Canada.
Breast cancer is a significant cause of death from cancer in women globally, highlighting the need for improved diagnostic imaging to enhance patient outcomes. Accurate tumor identification is essential for diagnosis, treatment, and monitoring, emphasizing the importance of advanced imaging technologies that provide detailed views of tumor characteristics and disease. Recently, a new imaging modality named synthetic correlated diffusion imaging (CDI) has been showing promise for enhanced prostate cancer delineation when compared to existing MRI imaging modalities.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29, Leninskiy Prospect, 119991 Moscow, Russia.
The molecular characteristics and rheological properties of three UHMWPE samples were investigated. The high-temperature GPC method was used for characterizing UHMWPE samples used. The interpretation of the measurement results was based on calibration using the PS standard and the approximation of the PS data by linear and cubic polynomials, as well as on the data for linear PE.
View Article and Find Full Text PDFMicromachines (Basel)
December 2024
NIST, Gaithersburg, MD 20899, USA.
We describe a modification of a previously described measurement-analysis protocol to determine the intrinsic properties of triaxial accelerometers by using a measurement protocol based on angular stepwise rotation in the Earth's gravitational field. This study was conducted with MEMS triaxial accelerometers that were co-integrated in four consumer-grade wireless microsensors. The measurements were carried out on low-cost rotation tables in different laboratories in different countries to simulate the reproducibility environment encountered in inter-comparisons of calibration capabilities.
View Article and Find Full Text PDFMolecules
December 2024
Department of Pharmaceutical and Pharmacological Sciences, Pharmaceutical Analysis, KU Leuven, 3000 Leuven, Belgium.
Analyzing and detecting endogenous amino acids in blood is of crucial importance for the diagnosis of medical conditions and scientific research. Considering the lack of UV chromophores in most of these analytes and the presence of several interfering substances in plasma, the quantification of quite a few amino acids and related compounds presents certain technical challenges. As a blank plasma matrix lacking these endogenous substances does not exist, the surrogate matrix method is used, as well as isotopic internal standards for calibration, to ensure the accuracy and reliability of the study.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
I2M (Institut de Mécanique et d'Ingénierie), UMR 5295, CNRS, University of Bordeaux, 33400 Talence, France.
From both economic and environmental points of view, the reuse of dredged sediments in the direct onsite casting of concrete represents a promising method for replacing sand. The aim of this study was to develop a cementitious material that (i) reuses the thin particles of sediments; (ii) has a low density due to the incorporation of air foam in the material; and (iii) achieves a minimum mechanical strength of 0.5 MPa for embankment applications.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!