Effectiveness of Crown Preparation Assessment Software As an Educational Tool in Simulation Clinic: A Pilot Study.

J Dent Educ

At the time this study was conducted, Ms. Tiu was a PhD candidate, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; Ms. Cheng was a dental student, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; Ms. Hung was a dental student, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; Ms. Yu was a dental student, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; Mr. Lin was a dental student, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; Dr. Schwass was Prosthodontist/Senior Lecturer, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand; and Dr. Al-Amleh was Prosthodontist/Senior Lecturer, Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand.

Published: August 2016

The aim of this pilot study was to evaluate the feasibility of a new tooth preparation assessment software, Preppr, as an educational tool for dental students in achieving optimal parameters for a crown preparation. In February 2015, 30 dental students in their fourth year in a five-year undergraduate dental curriculum in New Zealand were randomly selected from a pool of volunteers (N=40) out of the total class of 85. The participants were placed into one of three groups of ten students each: Group A, the control group, received only written and pictorial instructions; Group B received tutor evaluation and feedback; and Group C performed self-directed learning with the aid of Preppr. Each student was asked to prepare an all-ceramic crown on the lower first molar typodont within three hours and to repeat the exercise three times over the next four weeks. The exercise stipulated a 1 mm finish line dimension and total convergence angles (TOC) between 10 and 20 degrees. Fulfillment of these parameters was taken as an acceptable preparation. The results showed that Group C had the highest percentage of students who achieved minimum finish line dimensions and acceptable TOC angles. Those students also achieved the stipulated requirements earlier than the other groups. This study's findings provide promising data on the feasibility of using Preppr as a self-directed educational tool for students training to prepare dental crowns.

Download full-text PDF

Source

Publication Analysis

Top Keywords

educational tool
12
crown preparation
8
preparation assessment
8
assessment software
8
pilot study
8
dental students
8
group received
8
students achieved
8
students
6
group
5

Similar Publications

Introduction: Frailty, characterized by decreased resilience due to physiological decline, affects approximately 65% of community-dwelling elderly in Nepal. This study assessed frailty and its factors among hospitalized older adults in a tertiary hospital in Nepal.

Methods: This cross-sectional study included 124 participants aged 60 and above, admitted to a tertiary hospital in Nepal.

View Article and Find Full Text PDF

Through a literature review, expert interviews, questionnaires, and statistical methods, this study constructs an evaluation index system and calculates the score for the integrated development of sports, culture, and tourism at sports event venues, specifically the Hemei Rural Football Super League ("Village Super League") in Rongjiang, Guizhou. First, we reviewed and analyzed the relevant literature, which led to the formation of an initial index consisting of 18 items. The index was optimized after the analysis to include three main dimensions and 13 specific measurement items.

View Article and Find Full Text PDF

Agricultural waste or agro-waste, including natural fibers and particles from various crop parts, is increasingly recognized as a significant contributor to environmental issues. However, from a circular economy perspective, these materials present an opportunity to be repurposed into new, eco-friendly products. The present study, specifically focuses on understanding the effect of different factors, such as the particulate loading and the size (coir and hBN - 1 to 5 wt%; Coir Powder size (100-200 μm) of the particles on composite's corrosion rates and water absorption properties.

View Article and Find Full Text PDF

Background: The avoidable causes of infant mortality should be identified, and interventions should be made to improve the infant mortality rate. The cause of infant deaths should be assessed in both medical and social contexts.

Objectives: We aimed to determine the medical causes of infant mortality by verbal autopsy and its determinants in two rural blocks of the Khordha district of Odisha and assess the pathway of care and delay in seeking care for the illness preceding infant death using the three-delay model.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!